Heath Zenith SL-5411 - Manual
Heath Zenith SL-5411 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Wall Mount
- Page 3 – Bottom of Sensor
- Page 4 – TROUBLESHOOTING GUIDE; If you experience a problem, follow this guide.
- Page 5 – FUNCIONAMIENTO; Resumen de las modalidades del; PRUEBA; Requisitos
- Page 6 – INSTALACION; Montaje en pared
- Page 7 – Parte de abajo del detector
- Page 8 – GUIA DE INVESTIGACION DE AVERIAS; Si tiene algún problema siga esta guía.
- Page 9 – FONCTIONNEMENT; Résumé du mode de commutation; Exigences; Caractéristiques
- Page 10 – Montage mural
- Page 11 – Bas du détecteur
- Page 12 – GUIDE DE DÉPANNAGE; Si vous éprouvez des difficultés, suivre ce guide.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Auto
1, 5, 10 min.
x
Manual
Until Dawn*
x
OPERATION
© 2004 DESA Specialty Products™
595-5766-03
* resets to Auto Mode at dawn.
MANUAL MODE
ON-TIME
10 5 1 TEST
10 5 1 TEST
ON-TIME
TEST
... back on.
AUTO
1 Second OFF
then...
Put the ON-TIME switch in the 1, 5, or
10 minute position.
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the ON-
TIME switch in the 1, 5, or 10 position.
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
Requirements
• The Light Control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Model SL-5411
Light Control
Sensor
Cover
Plate
Lamp
Holders
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
Motion Sensor Light
Control for Canadian
Tire
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the
calibration time the control will be in the AUTO mode.
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Plastic Hanger
Rubber Plug
Gasket
Mounting Strap
Mounting Bolt
2 Wire
Connectors
This package includes:
6 Screws
(3 sizes included)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 595-5766-03 INSTALLATION For easy installation, select an existing light with a wallswitch for replacement. W IRE THE L IGHT C ONTROL . ❒ Turn power off at the fuse or circuit breaker. ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using two screwsthat fit your junction...
3 595-5766-03 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. Motion Motion The detector is most sensitive to motion across its fieldof view. ❒ Loosen the clamp screw inthe sensor ball joint and gen-tly rotate the sensor. ❒ Walk through the coveragearea noting where you arewhen t...
4 595-5766-03 SYMPTOM Lights will not comeon. L i g h t s c o m e o nin daylight. Lights come on forno apparent rea-son. POSSIBLE CAUSE 1. Light switch is turned off.2. F l o o d l i g h t i s l o o s e o r burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Daylight turn-off is in eff...
