Heath Zenith SH-5411 - Manual
Heath Zenith SH-5411 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Mode Switching Summary; MANUAL MODE; Eave Mount; INSTALLATION
- Page 4 – Bottom of Sensor; Least Sensitive; Motion
- Page 5 – before returning product to store.; No Service Parts Available for this Product; TEN YEAR LIMITED WARRANTY
- Page 6 – Requisitos; Características; FUNCIONAMIENTO; Prueba
- Page 7 – Resumen de las modalidades del; PRUEBA; Montaje en pared; INSTALACION
- Page 8 – Blanco
- Page 9 – PRUEBA Y AJUSTE; Parte de abajo del detector; Lo menos sensible
- Page 10 – GUIA DE INvESTIGACION DE AvERIAS; ESPECIFICACIONES
- Page 11 – SERvICIO TÉCNICO; pedir ayuda antes de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.; GARANTÍA LIMITADA A 10 AÑOS
- Page 12 – Caractéristiques; FONCTIONNEMENT; Exigences
- Page 13 – Résumé du mode de commutation; Montage sous; les commandes
- Page 14 – calfeutrer
- Page 15 – ESSAIS ET RÉGLAGES; Bas du détecteur; Portée maximale; FICHE TECHNIQUE
- Page 16 – GUIDE DE DÉPANNAGE; SERvICE TECHNIQUE; avant de retourner l’article au magasin.; Aucune pièce de rechange n’est disponible pour ce produit.
© 2008 HeathCo LLC
598-1157-05
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
•
S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
• The backplate has knockouts so the sensor can be
mounted on most junction boxes.
• In some applications a universal adaptor plate may
be needed. Adaptors are available at home centers
and electrical supply stores.
Light Control
Sensor
Cover
Plate
Lamp Holders
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
Gasket
2 Wire
Connectors
This package includes:
4 Screws
(2 sizes included)
OPERATION
* resets to Auto Mode at dawn.
TEST
10 5 1
TEST
ON-TIME
Put the ON-TIME switch on the
bottom of the sensor in the TEST
position.
MANUAL MODE
ON-TIME
10 5 1
TEST
... back on.
AUTO
1 Second OFF
then...
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Normal
1, 5, 10 min.
x
Manual
Until Dawn*
x
Model SH-5411
Motion Sensor
Light Control
Meets the ENERGY STAR
®
guidelines
when used with 120 W Max bulbs.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1157-05 For eave mount only: ❒ Swing the sensor head towards the clamp screw joint. If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done. ❒ Then rotate the sensor head clockwise 180° so the controls fac...
4 598-1157-05 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. ❒ Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. ❒ Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times when motion is detec...
5 598-1157-05 SYMPTOM Lights will not come on. L i g h t s c o m e o n in daylight. L i g h t s c o m e o n f o r n o a p p a r e n t reason. POSSIBLE CAUSE 1. Light switch is turned off. 2. F l o o d l i g h t i s l o o s e o r burned out. . Fuse is blown or circuit breaker is turned off. 4. Daylig...
