Heath Zenith SL-5326 - Manual

Heath Zenith SL-5326 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – INSTALLATION; Twist the junction box wires and fixture wires together; Wall Mount; WARNING: Turn power off at the fuse or circuit
Page 3 – TEST AND ADJUSTMENT; Motion; SPECIFICATIONS; RANGE; Bottom of Sensor; Least Sensitive
Page 4 – TROUBLESHOOTING GUIDE; TEN YEAR LIMITED WARRANTY; TECHNICAL SERvICE; No Service Parts Available for this Product
Page 5 – FUNCIONAMIENTO; Resumen de las modalidades del; PRUEBA; Requisitos; Características; Nota: Cuando lo prenda por primera vez espere 1; Prueba
Page 6 – INSTALACION; Entonces gire la cabeza del detector hacia la; Montaje en pared; ADvERTENCIA: Apague la energía en el fusible
Page 7 – Parte de abajo del detector; Lo menos sensible
Page 8 – GUIA DE INvESTIGACION DE AvERIAS; GARANTÍA LIMITADA A 10 AÑOS; SERvICIO TÉCNICO; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.
Page 9 – FONCTIONNEMENT; Résumé du mode de commutation; Exigences; Caractéristiques
Page 10 – Montage mural
Page 11 – Bas du détecteur; Portée maximale
Page 12 – avant de retourner l’article au magasin.

Loading the manual

OPERATION

595-4884-20

* resets to Auto Mode at dawn.

MANUAL MODE

ON-TIME

10 5 1 TEST

10 5 1

TEST

ON-TIME

TEST

... back on.

AUTO

1 Second OFF

then...

Put the ON-TIME switch in the
1, 5, or 10 minute position.

Put the ON-TIME switch on the bottom
of the sensor in the TEST position.

Manual mode only works at night
because daylight returns the sensor
to AUTO.

Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.

Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.

Move ON-TIME Switch to

1, 5, or 10 minutes

Mode Switching Summary

Flip light switch off

for one second then

back on*

MANUAL MODE

AUTO

TEST

Requirements

• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be

wired through a switch.

•

S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.

• This product is intended for use with the enclosed

gasket and with a junction box marked for use in wet
locations.

Model SL-5411

Light Control

Sensor

Cover

Plate

Lamp

Holders

Features

• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).

Motion Sensor Light
Control

* If you get confused while switching modes, turn the

power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.

Note: When first turned on wait about 1

minutes for

the circuitry to calibrate.

Plastic Hanger

Rubber Plug

Gasket

Mounting Strap

Mounting Bolt

2 Wire

Connectors

As an ENERGY STAR

Partner, Heath

/Ze-

nith has determined that this product meets
the ENERGY STAR

guidelines for energy

efficiency. This product is ENERGY STAR

compliant when used with 120 Watt bulbs.

This package includes:

6 Screws

(3 sizes included)

Mode:

On-Time

Works: Day Night

Test

5 Seconds

Auto

1, 5, or 10 Minutes

Manual

To Dawn*

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - INSTALLATION; Twist the junction box wires and fixture wires together; Wall Mount; WARNING: Turn power off at the fuse or circuit

2 595-4884-20 INSTALLATION For easy installation, select an existing light with a wall switch for replacement. W ire the L ight C ontroL ❒ Route the light control’s wires through the large gasket holes. ❒ Twist the junction box wires and fixture wires together as shown. Secure with wire connectors. ...

Page 3 - TEST AND ADJUSTMENT; Motion; SPECIFICATIONS; RANGE; Bottom of Sensor; Least Sensitive

3 595-4884-20 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. ❒ Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. Motion Motion The detector is most sensitive to motion across its field of view. ❒ Loosen the clamp screw in the sensor ball jo...

Page 4 - TROUBLESHOOTING GUIDE; TEN YEAR LIMITED WARRANTY; TECHNICAL SERvICE; No Service Parts Available for this Product

4 595-4884-20 SYMPTOM Lights will not come on. L i g h t s c o m e o n in daylight. L i g h t s c o m e o n f o r n o a p p a r e n t reason. POSSIBLE CAUSE 1. Light switch is turned off. 2. F l o o d l i g h t i s l o o s e o r burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Dayli...