Heath Zenith SL-5309 - Manual

Heath Zenith SL-5309 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – CAUTION to avoid fire or burn hazards:
Page 3 – Bottom of Sensor; SENS
Page 4 – TROUBLESHOOTING GUIDE; TECHNICAL SERvICE; No Service Parts Available for this Product
Page 5 – Requisitos; FUNCIONAMIENTO; INSTALACION; Resumen de las modalidades del interruptor; PRUEBA
Page 6 – Y C
Page 7 – ESPECIFICACIONES; Lo menos sensible; PRUEBA Y AJUSTE
Page 8 – GUIA DE INvESTIGACION DE AvERIAS; SERvICIO TÉCNICO; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.
Page 9 – Exigences; FONCTIONNEMENT; * Si vous ne savez plus dans quel mode se trouve; INSTALLATION; Résumé du mode de commutation
Page 11 – FICHE TECHNIQUE; ESSAIS ET RÉGLAGES; Portée maximale
Page 12 – GUIDE DE DÉPANNAGE; SERvICE TECHNIQUE; retourner l’article au magasin.

Loading the manual

Motion Sensor Quartz

Security Light

Model SL-5309

The Motion Sensor Quartz Security Light turns on 300
watts of quartz-halogen lighting when motion is detected
and then, after a selectable period of time, automati-
cally turns the lighting off. The built-in photocell keeps
the lighting off during daylight hours.

Cover

Plate

Sensor

3 Wire

Connectors

4 Screws

(2 sizes)

Light Control

Cover Plate

Gasket

595-5496-07

Halogen

Bulb

OPERATION

* resets to Auto Mode at dawn.

Requirements

• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must

be wired through a switch – not a dimmer or other
electronic switch.

•

Some codes require installation by a qualified
electrician.

• This product is intended for use with the enclosed

gasket and with a junction box marked for use in wet
locations.

• The backplate has knockouts so the sensor can be

mounted on most junction boxes.

• In some applications a universal adaptor plate may

be needed. Adaptors are available at Home Centers
and Electrical Supply Stores.

Long Bolt

This package includes:

Move ON-TIME Switch

to 1, 5, or 10 minutes

Mode Switching Summary

Flip switch off for

one second then

back on*

TEST

AUTO

MANUAL MODE

ON-TIME

* If you get confused while switching modes, turn the

power off for one minute, then back on. After the
calibration time (1

min.) the control will be in the

AUTO mode.

INSTALLATION

For easy installation, select an existing light with a wall
switch for replacement.

❒

Attach the lamp arm to

the backplate arm and
secure with the long
bolt.

Note:

When tightening the

arm screw, pull on the wires
to make sure the wires are not
pinched by the joint.

10 5 1

TEST

10 5 1

TEST

MANUAL MODE

AUTO

TEST

... back on.

1 Second OFF

then...

Manual mode only works at night
because daylight returns the sensor
to AUTO.

Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.

Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.

Put the ON-TIME switch on the bottom
of the sensor in the TEST position.

Put the ON-TIME switch in the 1, 5, or
10 minute position.

Mode:

On-Time

Works:

Day Night

Test

5 Seconds

Auto

1, 5, or 10 Min

Manual

Until Dawn*

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CAUTION to avoid fire or burn hazards:

2 595-5496-07 ❒ Drill out the holes if needed to mount the backplate to the junction box. ❒ Remove the existing light fixture. ❒ Strip about 5/8" (16 mm) insulation from the existing junction box wiring. ❒ Route the light control’s wires through the large hole in the gasket. ❒ Twist the junction...

Page 3 - Bottom of Sensor; SENS

3 595-5496-07 SPECIFICATIONS Range . . . . . . . . . . . . . Up to 60 ft. (18.3 m); [varies with surrounding temperature] Sensing Angle . . . . . . . Up to 110°Electrical Load . . . . . . . Up to 300 Watts Maximum Tungsten Power Requirements . . 120 VAC, 60 HzOperating Modes . . . . . TEST, AUTO and...

Page 4 - TROUBLESHOOTING GUIDE; TECHNICAL SERvICE; No Service Parts Available for this Product

4 595-5496-07 TROUBLESHOOTING GUIDE SYMPTOMLight will not come on. Light comes on in daylight. Light comes on for no apparent reason. POSSIBLE CAUSE 1. The halogen lamp is positioned too close to the light control’s sensor or pointed at nearby objects that cause heat to trigger the sensor. (Repositi...