Heath Zenith SL-5210 - Manual
Heath Zenith SL-5210 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION
- Page 4 – TROUBLESHOOTING GUIDE; No Service Parts Available for this Product; TECHNICAL SERVICE; FIVE YEAR LIMITED WARRANTY
- Page 5 – FUNCIONAMIENTO; Mueva el interruptor de tiempo; Resumen de las modalidades del interruptor; Apague el interruptor
- Page 6 – Diagrama del Alambrado; Montar Sensor; INSTALACION
- Page 8 – GUIA DE INVESTIGACION DE AVERIAS; GARANTÍA LIMITADA A 5 AÑOS; No hay piezas de servicio disponibles para este producto; SERVICIO TÉCNICO
- Page 9 – FONCTIONNEMENT; Résumé du mode de commutation
- Page 10 – Schéma de câblage; Montage du détecteur
- Page 11 – ESSAI ET RÉGLAGE; FICHE TECHNIQUE
- Page 12 – GUIDE DE DÉPANNAGE; GARANTIE LIMITÉE DE 5 ANS; Aucune pièce de rechange n’est disponible pour ce produit; SERVICE TECHNIQUE
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
Requirements
• The Light Control requires 120-volts AC.
• If you want to use Manual Override, the control must be
wired through a wall switch.
• Some codes require installation by a qualified electrician.
• Switch Module mounts into a standard 4" x 4" junction box.
The SL-5210 package includes:
• The Sensor Module and Switch Module
• Three wire nuts
• Two sensor module screws
© 2003 DESA Specialty Products™
595-4991-06
Motion Sensor
Decorative Lighting
Control
Model SL-5210
OPERATION
10 5 1 TEST
ON-TIME
TEST
* resets to Auto Mode at dawn.
ON-TIME
AUTO
... back on.
1 Second OFF
then...
MANUAL OVERRIDE
10 5 1 TEST
Switch
Module In
Junction Box
Behind Light
Fixture
Sensor Module
Sensor Cord
Existing Light Fixture
Typical Installation
Drip Loop
NOTE: The Drip Loop is neccessary to prevent rain from
running down the cord to the Sensor Module.
Move ON-TIME Switch to
1, 5 or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the power
off for one minute, then back on. After the calibration time
the control will be in the AUTO mode.
Note: When first turned on wait about 1
1
/
2
minutes for the
circuitry to calibrate.
Manual mode only works at night because
daylight returns the sensor to AUTO.
Flip the light switch off for one second then
back on to toggle between AUTO and
MANUAL MODE.
Manual mode works only with the ON-TIME
switch in the 1, 5, or 10 position.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Auto
1, 5, 10 min.
x
Manual
Until Dawn*
x
Put the ON-TIME switch on the bottom of
the sensor in the TEST position.
Put the ON-TIME switch in the 1, 5, or 10
minute position.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 595-4991-06 ❒ Plug the sensor cord into the switch module. The sensorcord's plug is polarized for proper installation. ❒ Place the Switch Module into the junction box. Beforemounting the fixture cover, make sure that the cord is flatand smoothly placed against the wall so that the cord willnot be ...
4 595-4991-06 SYMPTOM Light will notcome on. Light comes onin daylight. Light comes onfor no apparentreason. POSSIBLE CAUSE 1. A sensor is positioned too close to the lamp or pointed at nearby objects that cause heat to triggerthe sensor (Reposition the lamp away from the sensor or nearby objects). ...
5 595-4991-06 Características • Prende la luz cuando detecta movimiento.• Apaga la luz automáticamente.• La fotocélula mantiene la luz apagada durante el día. Requisitos • El Control de Luz requiere 120 VCA.• Para usar el Sobrecontrol Manual, conecte el control con un interruptor. • A l g u n o s c ...
