Heath Zenith SH-7001 - Manual

Heath Zenith SH-7001 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – teSt anD aDJuStMent; Least Sensitive; Maximum Range; adjustment of Coverage area; OPeratiOn; test; thingS tO reMeMBer
Page 3 – replace lamp only with same type lamp,
Page 4 – FiVe Year LiMiteD WarrantY; trOuBLeShOOting guiDe; SYMPtOM; teChniCaL SerViCe; before returning product to store.; the problem persists, call* for assistance at; no Service Parts available for this Product
Page 5 – DeSeMPaque; tres tornillos cónicos; Mantenga; Usted deberá apuntar de nuevo el panel solar de; dos tornillos de cabeza redonda; los orificios en la parte de atrás de la caja.; CaraCteríStiCaS; • No prenda la luz antes que la batería esté comple-
Page 6 – PrueBa Y aJuSte; regulación del Área de Cobertura
Page 7 – FunCiOnaMientO; Prueba; CaMBiO De La Batería; antes de la prueba mantenga el in-; PuntOS que Se DeBen; Cambie la lámpara con el mismo tipo de
Page 8 – guía De anÁLiSiS De aVeríaS; SíntOMa; garantía LiMitaDa a 5 aÑOS; SerViCiO tÉCniCO; pedir ayuda antes de devolver el producto a la tienda.; problema continúa, llame al; no hay piezas de servicio disponibles para este producto.
Page 9 – À suivre; DÉBaLLage; trois vis à tête; S’assurer que le joint à rotule; Vous devrez probablement réorienter le panneau; deux vis à tête ronde; CaraCtÉriStiqueS; période de lumière du jour.; exigenCeS; • Ne pas activer l’éclairage avant que la pile ne soit complè-
Page 10 – eSSai et rÉgLage; réglage de la Zone de Couverture; Note; Le moins sensible
Page 11 – FiChe teChnique
Page 12 – garantie LiMitÉe De 5 anS; guiDe De DÉPannage; SYMPtÔMe; SerViCe teChnique; de l’aide avant de retourner l’article au magasin.

Loading the manual

Solar Powered
Motion Sensor Light

Model SH-7001

FeatureS

• Turns on light when motion is detected.
• Automatically turns light off.
• Photocell keeps the light off during daylight hours.
•

Battery Protection Circuitry. Unit will shut down when
battery is low. Unit will automatically resume operation
when battery is recharged to a safe level.

requireMentS

• Do not turn the light on before the battery is fully charged.

Charge the battery by keeping the switch in the OFF
position and the solar collector pointed directly at the
noon sun for 3 sunny days. If not fully charged, the unit
will not work.

• When FULLY charged, the solar light will operate a

maximum of 15 days without sunlight. Actual operating
time will vary depending upon how frequently the light
is triggered.

Light

Battery
Case

Sensor

3. Mounting Screws (2 sizes)

1. Solar Light Fixture

2. Solar Panel

Tapered Screw (3)

Round Head Screw (2)

unPaCking

Be sure to remove all contents from packaging and verify
all items are present before assembling this light fixture.
This package includes the following items:

inStaLLatiOn

For best performance, mount the fixture about 8 feet (2.4
m) above the ground.

Mount solar panel base on a solid surface using

three tapered screws

. Adjust the panel to point directly

at the noon sun. Avoid obstructions such as trees or
buildings that may block sun light. Allow for enough
wire to reach the case.

keep ball joint at bottom.

Note:

You will want to re-aim the solar panel as the

seasons change to keep it pointed directly at the noon
sun.

Three Mounting Holes for Solar Panel Base

Mount the battery case on a solid surface using

two round-head screws

and the keyholes on the

back of the case.

adjust sensor. For proper operation, the sensor
head must be rotated so that the sensor controls face
downward as shown below.

Mounting Holes (3)

Mounting
Holes (2)

4. Plug the solar panel cable into the bottom of the battery

case.

IMPORTANT:

allow the battery to charge

with three days of sunshine before testing.

Controls

Light

Battery Case

Sensor Joint
Clamp

IMPORTANT:

the controls must face downward to

avoid damage from rain. If controls face upward, move
sensor to the original down position, rotate 180°, then
raise to the position shown below.

Light Joint Clamps

Lense Removal
Tab

Sensor

598-1164-04

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - teSt anD aDJuStMent; Least Sensitive; Maximum Range; adjustment of Coverage area; OPeratiOn; test; thingS tO reMeMBer

2 598-1164-04 teSt anD aDJuStMent NOTE: Sensor has a 30 second warm up period before it will detect motion. When switching modes wait 30 seconds. 1. Slide the sensor switch to the TEST (center) posi- tion. 2. Place the RANGE adjustment in the medium position (halfway between MIN and MAX position). L...

Page 3 - replace lamp only with same type lamp,

3 598-1164-04 SPeCiFiCatiOnS Range ........................... Up to 60 ft. (18.3 m); [varies with surrounding temperature] Sensing Angle .............. Up to 110°Lamp ............................. 15 watt, 6 volt halogenBattery Type .................. Sealed lead acid, 6 V 6.0 A-Hr.On Time ...........

Page 4 - FiVe Year LiMiteD WarrantY; trOuBLeShOOting guiDe; SYMPtOM; teChniCaL SerViCe; before returning product to store.; the problem persists, call* for assistance at; no Service Parts available for this Product

4 598-1164-04 FiVe Year LiMiteD WarrantY This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.For a period of five years from the date of purchase, any malfunction caused by factory defective parts o...