Heath Zenith SH-5412 - Manual
Heath Zenith SH-5412 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; NOTE: If fixture is mounted; Mode Switching Summary; Flip light switch; MANUAL MODE; Wall Mount
- Page 3 – Wire the Light Control
- Page 4 – Bottom of Sensor; Least Sensitive; Motion
- Page 5 – before returning product to store.; If the problem persists, call* for assistance at; No Service Parts Available for this Product; TEN YEAR LIMITED WARRANTY
- Page 6 – Requisitos; Características; FUNCIONAMIENTO; Prueba
- Page 7 – Resumen de las modalidades del; PRUEBA; INSTALACION; NOTA: Si el aparato está instalado a; Montaje en pared
- Page 8 – ADvERTENCIA: Desconecte la energía en el
- Page 9 – PRUEBA Y AJUSTE; Parte de abajo del detector; Lo menos sensible
- Page 10 – GUIA DE INvESTIGACION DE AvERIAS; ESPECIFICACIONES; y MODO MANUAL
- Page 11 – SERvICIO TÉCNICO; pedir ayuda antes de devolver el producto a la tienda.; Si el problema continúa, llame al; No hay piezas de servicio disponibles para este producto.; GARANTÍA LIMITADA A 10 AÑOS
- Page 12 – Exigences; Caractéristiques; FONCTIONNEMENT
- Page 13 – Placer l’interrupteur ON-; Résumé du mode de commutation; Mettre l’interrupteur; Montage mural; Puis faire pivoter le détecteur sur 180° de façon
- Page 14 – AvERTISSEMENT : Couper l’alimentation du
- Page 15 – ESSAIS ET RÉGLAGES; Bas du détecteur; Portée maximale; FICHE TECHNIQUE
- Page 16 – avant de retourner l’article au magasin.
© 2008 HeathCo LLC
598-1158-04
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
•
S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Light Control
Sensor
Cover
Plate
Lamp Holders
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Bulb Saver™ - Extends bulb life by up to 4x standard
bulbs. Lights bulb to full bright in under 2 seconds.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
Plastic Hanger
Rubber Plug
Gasket
Mounting Strap
Mounting Bolt
2 Wire
Connectors
This package includes:
6 Screws
(3 sizes included)
OPERATION
* resets to Auto Mode at dawn.
TEST
10 5 1
TEST
ON-TIME
Put the ON-TIME switch on the
bottom of the sensor in the TEST
position.
MANUAL MODE
ON-TIME
10 5 1 TEST
... back on.
AUTO
1 Second OFF
then...
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Normal
1, 5, 10 min.
x
Manual
Until Dawn*
x
Model SH-5412
Motion Sensor
Light Control
Meets the ENERGY STAR
®
guidelines
when used with 120 W Max bulbs.
2 Shells
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1158-04 INSTALLATION For easy installation, select an existing light operated by a wall switch for replacement.For best performance, mount the fixture about 8 feet (2.4 m) above the ground. NOTE: If fixture is mounted higher than 8 ft. (2.4 m), aiming the sensor down will reduce coverage dista...
3 598-1158-04 ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using two screws that fit your junction box. ❒ The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover pla...
4 598-1158-04 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. ❒ Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. ❒ Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times when motion is detec...
