Heath Zenith Multi-Channel Remote Control - Manual
Heath Zenith Multi-Channel Remote Control – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SEtuP ExaMPLE – SEt uP RECEIvERS
- Page 3 – ENGLISH; SPECIFICatIoNS; tRouBLESHootING GuIdE; REGuLatoRy INFoRMatIoN; No Service Parts available for this Product
- Page 4 – tWo yEaR LIMItEd WaRRaNty; Not Covered
- Page 5 – CaRaCtERíStICaS; INStaLaCIóN dE LaS PILaS; IdENtIFICaCIóN dEL PRoduCto
- Page 6 – EJEMPLo dE PRoGRaMaCIóN– PRoGRaMaCIóN dE LoS RECEPtoRES
- Page 7 – ESPECIFICaCIoNES; Guía dE aNáLISIS dE avERíaS; INFoRMaCIóN REGuLatoRIa; producto a la tienda.
- Page 8 – GaRaNtía LIMItada a 2 añoS
- Page 9 – télécommande; CaRaCtéRIStIquES; INStaLLatIoN dES PILES
- Page 10 – ExEMPLE dE RéGLaGE – RéGLaGE dES RéCEPtEuRS
- Page 11 – SPéCIFICatIoNS; GuIdE dE déPaNNaGE; RENSEIGNEMENtS dE RèGLEMENtS; l’article au magasin.
- Page 12 – GaRaNtIE LIMItéE dE 2 aNS; Exclusions de la garantie -
ENGLISH
© 2007 HeathCo LLC
598-1145-01
Multi-Channel Remote
Control
FEatuRES
• Operational range of up to 100 feet.
• Controls all Heath
®
/Zenith RF Tech Communica-
tions™ products.
• FCC/IC tested and approved.
• Flash control on compatible receivers when using
the Panic feature.
ALL ON
ALL OFF
OFF
DIM
PANIC
A
B
ON
BattERy INStaLLatIoN
The Multi-Channel Remote
Control is designed for 3
Volt operation:
1. Remove battery cover
on rear of housing by
pushing clip and lifting
up.
2. I n s t a l l 2 - A A A b a t -
teries (not included)
according to polarity
markings. For best per-
formance use alkaline
batteries.
Battery Cover
Two AAA Batteries
(Not Included)
Installing 2-AAA Batteries
PRoduCt IdENtIFICatIoN
*dIM Control:
Dims lighting controls that are equipped with the dimming feature. Pressing DIM will toggle through the different dim
levels. Each time the DIM button is pressed, the control LED will momentarily light.
The receiver saves the last dim setting used. To recall the last dim setting, press the DIM control once.
Note: Not all lighting controls have the DIM and PANIC (flash) feature.
Control Group and Indicators - Select
Group A or B lighting controls.
ALL ON - Turns all lights within a Group ON.
Select either Group A or B then press ALL ON.
Light Control - ON
PANIC* - All lights within a Group will
flash ON and OFF. Select either Group A
or B then press PANIC.
ALL OFF - Turns all lights within a
Group OFF. Select either Group A or
B then press ALL OFF.
Control Identification - Remove clear plastic film by
placing two fingers on the plastic and “pinching” the
plastic. Remove card. Write on the card to label each
control. Replace card and plastic film.
Light Control - OFF
Light Control Selectors
Light Control - DIM*
ON
ALL ON
ALL OFF
DIM
PANIC
A
B
OFF
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1145-01 SEtuP ExaMPLE – SEt uP RECEIvERS Following is one example of how the Lighting Control Panel can be programmed to operate multiple light sources within a home.The Control Panel has two “Groups” (A and B) with up to eight lighting controls in each group. In this example, the eight contro...
3 598-1145-01 ENGLISH SPECIFICatIoNS Range ....................................................................................................................................................................Up to 100 feet (30.5 m)Rated Voltage (2-AAA Batteries) .........................................
4 598-1145-01 tWo yEaR LIMItEd WaRRaNty This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.For a period of two years from the date of purchase, any malfunction caused by factory defective parts or ...
