Heath Zenith 9700LeD - Manual
Heath Zenith 9700LeD – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Wiring the Light COntrOL; Warning: turn power off at circuit breaker; mOunt the Light COntrOL
- Page 3 – testing anD aDJustments; Maximum Range; Bottom of sensor; Least Sensitive
- Page 4 – OperatiOn; test; mODe sWitChing summary; speCiFiCatiOns
- Page 5 – trOuBLeshOOting guiDe
- Page 6 – tWO year LimiteD Warranty
- Page 7 – Control de luz del; instaLaCiOn; nOta: Si el aparato está instalado a; sólo para montaje eléctrico:; montaje en alero
- Page 8 – aDvertenCia: Desconecte la energía en; COneCte eL COntrOL De Luz
- Page 9 – prueBas y aJustes; Alcance Máximo; parte de abajo del detector; Lo menos sensible; Nota
- Page 10 – OperaCiÓn; prueba; resumen De Las mODaLiDaDes; PRUEBA; Fase De sOBre COntrOL manuaL; espeCiFiCaCiOnes
- Page 11 – guia De investigaCiOn De averias
- Page 12 – garantÍa LimitaDa De DOs aÑOs
- Page 13 – Commande d’éclairage à; instaLLatiOn; montage sous
- Page 14 – mise en garDe : Coupez l’alimentation; mOntage De La COmmanDe
- Page 15 – essais et rÉgLages; Bas du détecteur; Portée maximale
- Page 16 – FOnCtiOnnement; essai; rÉsumÉ Du mODe De COmmutatiOn; mODe COntOurnement manueL; FiChe teChnique
- Page 17 – guiDe De DÉpannage
- Page 18 – garantie LimitÉe De DeuX ans
Dated receipt required for warranty replacement.
Features
• Automatically comes on when motion is detected.
• Automatically turns light off.
• Photocell keeps the light off during daylight
hours.
• LED indicates motion was sensed (day or night).
requirements
• The light control requires 120 volts AC.
• If you want to use Manual Override mode, the
control must be wired through a switch.
nOtiCe: Not to be used on light dimmer or timer-
controlled circuits.
•
some electrical codes require installation by a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in
wet locations.
• This light fixture has been tested/certified using
Lights of America LED Lamp Model Numbers
2 0 0 3 L E D P 3 8 - 6 5 K , 2 0 0 2 L E D R 3 0 - 6 5 K , a n d
2002LEDP30-65K.
unpaCking
Be sure to remove all contents from packaging and
verify all items are present before assembling this light
fixture. This package includes the following items:
• Security Light
• Two LED PAR38 lamps
(Lights of America Model: 2003LEDP38-65K)
• Two decorative lamp shells
• Mounting Strap
• Plastic Hanger
• Rubber Plug
• Mounting hardware
• Wire nuts
• Owner’s Manual
© 2008
598-1360-00
motion sensor
Light Control
model: 9700LeD series
instaLLatiOn
For easy installation, select an existing light with a
wall switch for replacement.
For best performance, mount the fixture about 8 ft.
(2.4 m) above the ground.
nOte: If fixture is mounted
higher than 8 ft. (2.4 m), aiming the sensor down will
reduce coverage distance.
For eave mount only:
1. Swing the sensor head towards the clamp screw
joint.
For under eave installation, the sensor head must
be rotated as shown in the next two steps for proper
operation and to avoid the risk of electrical shock.
Controls
Controls
Controls
eave mount
Wall mount
Clamp Screw
2. Then rotate the sensor head clockwise 180° so
the controls face down.
If the sensor pops out of the ball joint, loosen the
clamp screw and push the sensor back into the ball
joint. Tighten the clamp screw when done.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1360-00 Wiring the Light COntrOL Warning: turn power off at circuit breaker or fuse. mOunt the Light COntrOL 1. Align the light control cover plate and cover plate gasket. Secure with the mounting bolt. 2. Align the three slots in the decorative shell with the lamp holder pins. Push the shell ...
3 598-1360-00 testing anD aDJustments 1. turn on the circuit breaker and light switch. Motion Motion nOte: If fixture is mounted higher than 8 ft. (2.4 m), aiming the sensor down will reduce coverage distance.The detector is less sensitive to motion directly towards it. Maximum Range Maximum Coverag...
4 598-1360-00 Note: When first turned on wait about 1 1 / 2 minutes for the circuitry to calibrate. * resets to Security mode at dawn. OperatiOn Mode: On-Time Works: Day Night test 5 Seconds x x security 1, 5 or 10 Minutes x manual Override Until Dawn* x MANUAL MODE AUTO TEST ON-TIME Switch at 1, 5,...
