Heath Zenith 598-1313-00 - Manual
Heath Zenith 598-1313-00 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CHimE REplaCEmEnt installation; Proper installation requires a diode on the front; Electrical work must be in accordance with national and local; Figure 1 - Electronic Chime Identification
- Page 3 – Figure 2 - Mounting Chime Base to Wall
- Page 4 – to select a tune to play Each time the push; Turn or slide the tune selection switch (depending upon model)
- Page 5 – DioDE installation instRuCtions; If not already installed on push button, attach
- Page 6 – tRouBlEsHootinG; Chime does not sound:; Check Diode on Front push Button:; if a diode is installed on more than one push button.
- Page 7 – If the problem persists,; no service parts available for this product
- Page 8 – Chime System Wiring Diagram
- Page 10 – La instalación correcta requiere un diodo en el; El trabajo eléctrico debe estar conforme a los códigos eléc-; Figura 1 - Identificación de la campana electrónica; Una clavija de la tapa está instalada en los dos lados de la base
- Page 11 – Figura 2 - Montaje de la base de la campana en la pared
- Page 12 – sElECCiÓn DEl tono; para seleccionar un tono que suene cada vez que; Gire o deslice (dependiendo del modelo) el interruptor selector
- Page 13 – instRuCCionEs DE instalaCiÓn DEl DioDo; Si aún no
- Page 14 – anÁlisis DE avERÍas; inspeccionar la campana:; la campana suena pero el tono suena incompleto:; inspeccionar el diodo en el botón delantero:; Algunos pulsadores vienen con los diodos instala-
- Page 15 – producto a la tienda.; Si el problema continúa, llame al; no hay piezas de servicio disponibles para este producto.
- Page 16 – Esquema eléctrico del sistema de la campana
- Page 18 – installation Du CaRillon DE RECHanGE; L’installation appropriée exige une diode dans; Les travaux d’électricité doivent être conformes aux codes; Dans; Figure 1 - Carillon électronique
- Page 19 – Figure 2 - Fixation du socle du carillon au mur
- Page 20 – sÉlECtion DE la tonalitÉ; pour sélectionner la tonalité diffusée chaque fois; Figure 3 - Câblage du carillon électronique
- Page 21 – DiRECtivEs D’installation DE la DioDE; le carillon ne diffuse pas toute la tonalité, consultez la section
- Page 22 – DÉpannaGE; le carillon n’émet pas de son; vérifiez le carillon :; le carillon se déclenche, mais ne diffuse pas toute la tonalité :; vérifiez la diode du bouton-poussoir de l’entrée principale :; Vérifiez si la diode est bien raccordée au bouton-poussoir (voir
- Page 23 – GaRantiE limitÉE DE 1 an; sERviCE tECHniQuE; de retourner l’article au magasin.
- Page 24 – Diagramme de câblage du carillon
P.O. Box 90004
Bowling Green, KY 42102-9004
© 2007 HeathCo LLC
598-1313-00
Hardwired
Electronic
Chime
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- 598-1313-00 CHimE REplaCEmEnt installation IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 13 below. Note: Electrical work must be in accordance with national and local electrical codes. ...
-3- 598-1313-00 8. Determine mounting location. Note: The back of the chime base is recessed to allow the base to cover the wire hole in the wall when mounting the base to the wall. 9. Mount chime base to wall using screws and anchors provided (see Figure 2). (Drill 7/32" diameter pilot hole for...
-- 598-1313-00 F T R 10. Connect wire “F” to screw terminal marked “FRONT”. Connect wire “T” to screw terminal marked “TRANS”. Connect wire “R” to screw terminal marked “REAR” (See Figure 3). Note: Some installations may not include rear door push button. 11. Connect diode to front push button (see ...
