Heath Zenith 598-1281-02 - Manual

Heath Zenith 598-1281-02

Heath Zenith 598-1281-02 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – Installation; DO NOT install addi-
  • Page 4 – Do; NOT; connect push; Tone Bar; Plunger; Determine Chime Type; Locate your chime and remove the
  • Page 5 – If you have an electronic chime, move
  • Page 6 – Troubleshooting; • Disconnect wires from button and touch
  • Page 7 – speaking only) for assistance before; If the; No Service Parts Available for this
  • Page 8 – ONE YEAR LIMITED WARRANTY
  • Page 9 – • El pulsador viene calibrado de fábrica; Pulsador
  • Page 10 – Instalación
  • Page 12 – Barra de tonos; Émbolo; Determine el tipo de campana; Vaya a su campana y retire la tapa.
  • Page 13 – Si tiene una campana electrónica,
  • Page 14 – Una vez que el pulsador y la campana; Análisis de averías; • D e s c o n e c t e l o s c o n d u c t o r e s d e l
  • Page 15 – Servicio Técnico; producto a la tienda.; Si el problema continúa,; No hay piezas de servicio disponibles
  • Page 16 – GARANTÍA LIMITADA A 1 AÑO
  • Page 17 – DEL avec éclairage; • Le bouton-poussoir est réglé en usine
  • Page 19 – Raccordez les deux fils du carillon et du
  • Page 20 – Ne connectez; PAS; le; Barre; Piston; Détermination du type de carillon; Si vous avez un carillon mécanique, passez
  • Page 21 – S i v o u s p o s s é d e z u n c a r i l l o n
  • Page 22 – Le bouton-poussoir doit être; Dépannage; • Débranchez les fils du bouton-poussoir
  • Page 23 – Service Technique; obtenir de l’aide avant de retourner; (service en anglais; Aucune pièce de rechange n’est
  • Page 24 – GARANTIE LIMITÉE DE 1 AN
Loading the manual

LED Lighted

Push Button with

Keyfinder Light

© 2007 HeathCo LLC

598-1281-02

• The push button is set from the factory

for use with mechanical chimes, but
can be used with either mechanical or
electronic chimes.

• Follow these instructions to install your

push button and set it to work with your
particular chime.

IMPORTANT:

Push button must be

installed with keyfinder light facing
downward.

Keyfinder
Lens

Push
Button

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Installation; DO NOT install addi-

598-181-0 1. Using a small screwdriver, push in tab on bottom of push button to remove back (see Figure 1). 2. Insert wires through hole in center of push button back. Attach back to wall with screws provided (see Figure 2). Installation IMPORTANT: DO NOT install addi- tional diode(s) to push button...

Page 4 - Do; NOT; connect push; Tone Bar; Plunger; Determine Chime Type; Locate your chime and remove the

598-181-0 CAUTION: Do NOT connect push button to mechanical chime if push button jumper is set for electronic chime use. Doing so may result in permanent damage to your chime. FR ONT TR A N S REAR DO NO T OIL Tone Bar Figure 4 - Inside Typical Mechanical Chime Plunger Determine Chime Type 5. Locate ...

Page 5 - If you have an electronic chime, move

5 598-181-0 Figure 5 - Determining Correct Jumper Position (Back of Push Button) Jumper On Two Top Pins for Electronic Chime 7. If you have an electronic chime, move the jumper on the back of your push button from the two bottom pins to the two top pins (see Figure 5). Press push button to test agai...

Other Heath Zenith Models

All Heath Zenith Other