Heath Zenith 598-1226-01 - Manual

Heath Zenith 598-1226-01

Heath Zenith 598-1226-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 2 – UP; JUMPER POSITION; Mounting Holes; Installation; DO NOT install additional
  • Page 3 – Do; NOT; Tone Bar; Plunger; Determine Chime Type; Locate your chime and remove the
  • Page 4 – If you have an electronic chime,
  • Page 5 – Troubleshooting; • Disconnect wires from button and touch; Technical Service; speaking only) for assistance before; If the; No Service Parts Available for this
  • Page 6 – ONE YEAR LIMITED WARRANTY
  • Page 7 – • El pulsador viene calibrado de fábrica; Reflector de LED regulable; Aleta de posición del reflector
  • Page 8 – Instalación; Orificios de montaje
  • Page 9 – Barra de tonos; Émbolo; Determine el tipo de campana; Vaya a su campana y retire la tapa.
  • Page 10 – Si tiene una campana electrónica
  • Page 11 – Análisis de averías; • D e s c o n e c t e l o s c o n d u c t o r e s d e l; Servicio Técnico; producto a la tienda.; Si el problema continúa,; No hay piezas de servicio disponibles
  • Page 12 – GARANTÍA LIMITADA A 1 AÑO
  • Page 13 – • Le bouton-poussoir est réglé en usine; Réflecteur à DEL réglable; Onglet de positionnement
  • Page 14 – Fils du carillon et du transformateur
  • Page 15 – Ne connectez; PAS; le; Barre; Piston; Détermination du type de carillon; Si vous avez un carillon mécanique, passez
  • Page 16 – Si vous avez un carillon électronique,
  • Page 17 – Dépannage; • Débranchez les fils du bouton-poussoir; Service Technique; obtenir de l’aide avant de retourner; (service en anglais; Aucune pièce de rechange n’est
  • Page 18 – GARANTIE LIMITÉE DE 1 AN
Loading the manual

LED Lighted

Pushbutton with

Courtesy Light

© 2007

598-1226-01

• The pushbutton is set from the factory

for use with mechanical chimes, but
can be used with either mechanical or
electronic chimes.

• Follow these instructions to install your

pushbutton and set it to work with your
particular chime.

Adjustable LED Reflector

The reflector has a 75 degree rotation to
allow the light to be directed as needed.
To adjust the reflector, slide reflector
positioning tab to desired location.

Reflector Positioning Tab

Clear Lens

Pushbutton

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - UP; JUMPER POSITION; Mounting Holes; Installation; DO NOT install additional

598-16-01 1. Attach the two wires from your chime and transformer to the screw terminals on the back of your pushbutton (see Figure 1). Press pushbutton to test function. 2. If your chime functions correctly and plays the entire tune, skip to step 7. If your chime does not function correctly, procee...

Page 3 - Do; NOT; Tone Bar; Plunger; Determine Chime Type; Locate your chime and remove the

598-16-01 CAUTION: Do NOT connect push- button to mechanical chime if pushbut-ton jumper is set for electronic chime use. Doing so may result in permanent damage to your chime. FR ONT TR A N S REAR DO NO T OIL Tone Bar Figure 2 - Inside Typical Mechanical Chime Plunger Determine Chime Type 3. Locate...

Page 4 - If you have an electronic chime,

598-16-01 Figure 3 - Determining Correct Jumper Position (Back of Pushbutton) UP JUMPER POSITION SEE OWNER’S MANUAL FOR DETAILS MECHANICAL CHIME ELECTRONIC CHIME Jumper On Two Right Pins for Electronic Chime UP JUMPER POSITION SEE OWNER’S MANUAL FOR DETAILS MECHANICAL CHIME ELECTRONIC CHIME Jumper O...

Other Heath Zenith Models

All Heath Zenith Other