Heath Zenith 598-1123-02 - Manual
Heath Zenith 598-1123-02 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Code and Tune Settings; Code Settings
- Page 3 – Tune Settings; Ding tune and the front door use; Replacing Push Button Batteries
- Page 4 – before returning product to store.; No Service Parts Available for this Product; Regulatory Information
- Page 5 – THREE YEAR LIMITED WARRANTY
- Page 6 – Ubique en la pared una caja eléctrica rectan-; Campana Mecánica; Tienda a la caja eléctrica un cableado
- Page 7 – Programaciones del código y del tono; Programaciones del código
- Page 8 – Programación del tono; Reemplazo de las baterías del pulsador
- Page 9 – Análisis de Averías; Servicio Técnico; pedir ayuda antes de devolver el producto a la tienda.; Información Regulatoria
- Page 10 – GARANTÍA LIMITADA A 3 AÑO
- Page 11 – Trouvez dans le mur une boîte électrique; Carillon mécanique; Acheminez le câblage vers la boîte électrique
- Page 12 – Réglages du code et de la mélodie; Réglages du code
- Page 13 – Remplacement des piles de l'unité de bouton-poussoir
- Page 14 – Dépannage; Service Technique; obtenir de l’aide avant de retourner l’article au magasin.; Renseignements de règlements
- Page 15 – GARANTIE LIMITÉE DE 3 AN
- Page 16 – No de modelo / N° de modèle
This package includes (Style of push button and chime may vary from illustration):
• Wireless chime
• Wireless push button w/battery (Specific models include 2)
• Hardware pack
This device is for use with 120VAC, 60 Hz. Do noT exceeD recom-
menDeD volTage.
Wireless Mechanical
Chime
© 2007 Heathco llc
598-1123-02
Figure 2
Figure 1
1. Install two lithium type CR1220 3 volt push
button batteries (included). remove back of
case by pushing in tab on bottom with a small
screwdriver. make sure batteries are oriented
properly (see page 3).
2. Locate an approved, vertically mounted,
single gang, rectangular electrical box in
the wall. It is recommended that the chime be
located approximately six (6) feet above the floor
for best sound travel and appearance.
WARNING: Turn power off at circuit
breaker or fuse.
3. Run wiring to electrical box using approved
wiring. connect the two wires from the house
wiring using supplied Ul approved wire nuts.
connect the black wire from chime to the black
wire from house. connect the white wire from
chime to the white wire from house.
4. Mount chime and push button. attach chime
unit to rectangular electrical box using two
screws provided. Insert screws into screw holes
as shown in Figure 2. Note: chime can only be
mounted in vertical position. Use arrow on rear
of chime unit as a guide. Turn on household
power.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- 598-1123-02 To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1).attach back of case to door jamb or wall. Snap front of push button on. Code and Tune Settings Code Settings Note: Most installations will not require you to change any code ...
-3- 598-1123-02 Tune Settings Your wireless chime has different selectable tunes: Ding (one note) and Ding- Dong (two note). The factory setting is for the Ding-Dong tune. This tune can be changed by following the instructions below.• Ding (one note tune) In Push Button only - Set dip switch 8 to “o...
-4- 598-1123-02 Troubleshooting Chime does not sound:• make sure push button and chime codes are the same (See pages 2 and 3).• check orientation of push button and chime batteries (if applicable) (See page 3). • check charge of push button and chime batteries (if applicable), replace if necessary. ...
