Heath Zenith 598-1119-05 - Manual
Heath Zenith 598-1119-05 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INDOOR PLUG-IN RECEIVER; INDOOR/OUTDOOR RECEIVER; Operation
- Page 3 – CHANNEL SETTINGS; To change the channel, slide dip switches to; ON; DIP SWITCH LOCATIONS
- Page 4 – POSSIBLE CAUSE
- Page 5 – ONE YEAR LIMITED WARRANTY
- Page 6 – CARACTERÍSTICAS; Productos a control remoto; Operación; CONTROL REMOTO DE 2 BOTONES; © 2003 DESA Specialty ProductsTM
- Page 7 – RECEPTOR PARA INTERIORES /
- Page 8 – CALIBRACIONES DEL CANAL; Nota: Las calibraciones del interruptor; UBICACIONES DE LOS
- Page 9 – GUÍA DE ANÁLISIS DE AVERÍAS; CAUSA PROBABLE
- Page 10 – GARANTÍA LIMITADA A 1 AÑO
- Page 11 – CARACTÉRISTIQUES; PRODUITS TÉLÉCOMMANDÉS; Fonctionnement; TÉLÉCOMMANDE À DEUX BOUTONS
- Page 12 – EXTÉRIEUR
- Page 13 – RÉGLAGE DES VOIES; télécommande et du récepteur.; EMPLACEMENT DES
- Page 14 – GUIDE DE DÉPANNAGE; CAUSE POSSIBLE
- Page 15 – GARANTIE LIMITÉE DE 1 AN
© 2003 DESA Specialty Products™
598-1119-05
FEATURES
• Quickly add ON/OFF control of a receptacle without the expense of new wiring.
• Four selectable channels allowing the use of up to four separate systems in the same home.
• Products are UL/cUL and/or FCC/IC tested and approved.
• Operational range of up to 50 feet.
Remote Controlled Products
Operation
1. The two buttons on the remote
will operate one or more receiver
units with matching channels.
Note: Receivers must be at least
10 feet apart for best performance.
2. Push the ON button to turn the
plugged in receiver on or the OFF
button to turn the plugged in re-
ceiver off.
Battery Replacement
The remote control requires a type A23 12 Volt
alkaline battery to operate. The remote control is
shipped with the battery installed. With typical
use, the battery will last approximately one year.
Remove battery when remote will not be used for
an extended period of time.
To replace the battery, follow the instructions
below:
1. Place remote control face down on a flat
surface.
2. Remove screw on bottom of remote with a
small phillips-head screwdriver.
2-BUTTON REMOTE CONTROL
ON
OF
F
3. Gently insert a small flat-head screwdriver
between the two halves on the bottom of the
remote and twist. Carefully separate the
back of the remote from the front.
4. Lift the back of the remote up and lay aside.
5. Remove battery. Install replacement bat-
tery. Make sure battery is oriented properly
(see illustration).
6. Reassemble remote in reverse order.
Inside of Remote Control
ON
12 V
1 2
Battery
Compartment
(Type A23)
Removing Back of Remote Control
Flat-Head
Screwdriver
Philips-Head
Screw
Remote
Control Back
ON
OF
F
This manual applies to the following products:
2-Button Remote Control
Indoor Plug-In Receiver
Indoor/Outdoor Receiver
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1119-05 INDOOR PLUG-IN RECEIVER Features and Ratings:• Up to 500 Watt maximum incan- descent load. • Up to 300 Watt maximum fluo- rescent load. • Up to 400 Watt maximum TV load. • Up to 1/3 Hp maximum motor load.• No wiring required. Operation Note: When using two or more receivers, thereceive...
3 598-1119-05 CHANNEL SETTINGS Note: The channel is factory set. Most instal-lations will not require you to change the twodip switches on your remote control or re-ceiver.Note: If purchasing more than one remotecontrol system, select different operatingchannels unless you want one remote con-trol t...
4 598-1119-05 REGULATORY INFORMATION This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subjectto the following two conditions: (1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interfe...
