Heath Zenith 598-1116-10 - Manual

Heath Zenith 598-1116-10

Heath Zenith 598-1116-10 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
Page: / 40

Table of Contents:

  • Page 2 – CODE SWITCH LOCATIONS; ON
  • Page 3 – ENGLISH; REmOTE CONTROL; Rear View of Remote Control; Code Settings; Left Side; Troubleshooting Guide
  • Page 4 – Battery Replacement; Removing Battery Tab; Removing Access Door; Operation; Receiver
  • Page 5 – ENTRY SWITCH; Installation; Important Considerations:; mounting configurations and possible directions of movement.; and magnet must be flush. If magnet is recessed, use magnet
  • Page 6 – Battery Compartment; INDOOR AND OUTDOOR; Select Night or 24 Hour mode; Attaching Ball Mounting Bracket to Indoor Motion Sensor; Installing Indoor Motion Sensor Using Optional; down to give you the desired coverage above the floor level.
  • Page 7 – Attaching Indoor Motion Sensor to Mounting Bracket; Installing Indoor Motion Sensor directly To wall; between waist and shoulder level above the floor (; Attaching Indoor Motion Sensor Directly to Wall; Installing Outdoor motion Sensor; When first turned on or when switching modes wait 30; Indoor Motion Sensor -
  • Page 8 – The detector is most sensitive to motion across its field of view.; Aim Sensor Down
  • Page 9 – RECEIVER InfORMATIOn; • When first turned on wait 15 seconds.; IndOOR PLUG-In COnVERTER; Control Locations; LAMP SOCkET COnVERTER
  • Page 10 – Junction box ground wire to green; Wiring Floodlight; White; FLOODLIGHT; The plastic hanger can be used to hold the fixture while
  • Page 11 – TROUBLEShOOTInG GUIdE; POSSIBLE CAUSE; REGULATORY INFORmATION; no Service Parts Available for this Product
  • Page 12 – TWO YEAR LImITED WARRANTY; incorporate new features in products previously sold.
  • Page 13 – CARACTERISTICAS; Los controles inalámbricos Heath; Productos a control remoto; con bombillas incandescentes o halógenas de 120 voltios.; – Reflector; CALIBRACIOnES dEL CÓdIGO; La mayoría de instalaciones de sólo un sistema no re-; Ejemplo 1 - Calibraciones del código, sistema 1; Guía de Análisis de Averías.; Ejemplo 2 - Calibraciones del código, sistema 2
  • Page 14 – UBICACIOnES dE LOS InTERRUPTORES dE CIRCUITO IMPRESO; Reflector
  • Page 15 – Guía; Presilla opcional del visor del carro (incluida); Calibraciones del Código; Lado izquierdo; Retiro de la presilla del visor – Vista posterior; CONTROL REmOTO; OFF; Vista posterior del control remoto
  • Page 16 – Reemplazo de la batería; InTERRUPTOR A AñAdIBLE; Instalación; Interruptor A añadible; Operación; Retiro de la aleta de la batería; Retiro de la tapa de
  • Page 17 – INTERRUPTOR DE ENTRADA; Consideraciones importantes:; Disposiciones de montaje y direcciones posibles del; Montaje con tornillo:
  • Page 18 – Seleccione modo nocturno o modo de 24 horas; noche o sólo por la noche. Para fijar el modo de detección, retire; Instalación de las baterías; Compartimento de la batería; Sujeción de la consola de montaje tipo bola al; Instalación del detector de movimiento para uso; Continuación
  • Page 19 – Sujeción del detector de movimiento para uso interior a la; Fijación del detector de movimiento directamente a la pared
  • Page 20 – Instalación del detector de movimiento; Revisión de la operación y de la regulación; detector de movimiento para uso interior -
  • Page 21 – cobertura menor
  • Page 22 – INFORmACIÓN DEL RECEPTOR; • Clasificado para un voltaje de alimentación de 120 V CA/60Hz.; COnVERTIdOR EnChUfABLE PARA; Ubicación de los controles; COnVERTIdOR dEL ZÓCALO dE LA
  • Page 23 – Cableado del reflector; Blanco; REFLECTOR; AdVERTEnCIA: desconecte la alimentación en el fusible; el orificio grande del empaque.; AdVERTEnCIA: Riesgo de incendio. no apunte
  • Page 24 – CAUSA PROBABLE; Verifique que el disyuntor o el fusible; SERVICIO TÉCnICO; producto a la tienda.
  • Page 25 – GARANTÍA LImITADA A 2 AñOS
  • Page 26 – CARACTÉRISTIQUES; Produits Télécommandés; • UTILISER SEULEmENT; RÉGLAGE dES COdES; Exemple 3 - Réglage des codes avec un seul; Guide de dépannage
  • Page 27 – Convertisseur enfichable intérieur; EMPLACEMEnT dES MICRO-InTERRUPTEURS; rupteurs vise à préciser la position à la; Détecteur de mouvements sans fil
  • Page 28 – Réglages des codes; Côté gauche; permettre à la transmission de s’effectuer.; Pince de pare-soleil d’automobile facultative; Pour attacher la pince de pare-soleil à la télécommande (si; TÉLÉCOMMAndE; appuyant sur le bouton DIM, vous avez accès à cinq degrés
  • Page 29 – Remplacement de la pile; Retrait de la porte d’accès; INTERRUPTEUR D’APPOINT; Retrait de l’onglet de la pile; Interrupteur d’appoint; Fonctionnement; Informations sur le récepteur
  • Page 30 – InTERRUPTEUR d’EnTRÉE; Retrait de l’onglet de pile; Configurations d’installation et possibilités de déplacement; Au moyen de vis :
  • Page 31 – Compartiment des piles; Sélection du mode de nuit ou du mode 24 heures; Installation du détecteur de mouvements intérieur; Fixation du support pivotant à bille au détecteur de mouve-; dÉTECTEURS dE MOUVEMEnT SAnS fIL
  • Page 32 – Installation du détecteur de mouvements intérieur sur le; Installation du détecteur de mouvements intérieur directe-
  • Page 33 – Installation du détecteur de mouvements extérieur; Note; Vérification du fonctionnement et du réglage; détecteur de mouvements intérieur -; Installation du détecteur de mouvement
  • Page 34 – Le détecteur est plus sensible au mouvement à travers son; couverture courte; Mouvement
  • Page 35 – InfORMATIOnS SUR LE RÉCEPTEUR; Emplacements des commandes; COnVERTISSEUR dE dOUILLE
  • Page 36 – Câblage du projecteur; Blanc; PROJECTEUR; AVERTISSEMEnT: Coupez le courant au fusible ou au
  • Page 37 – RENSEIGNEmENTS DE RèGLEmENTS; CAUSE POSSIBLE; SERVICE TEChnIQUE; l’article au magasin.
  • Page 38 – GARAnTIE LIMITÉE dE 2 AnS; ou de main-d’oeuvre sera corrigée gratuitement.; Exclusions de la garantie -
  • Page 40 – no de modelo / n° de modèle
Loading the manual

ON

1 2 3

4

ON

1 2 3

4

ON

1 2 3

4

ON

1 2 3

4

ON

1 2 3

4

ON

1 2 3

4

ENGLISH

Remote Controlled Products

This manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the same

code setting information. Please read all instructional information and note any specific information pertaining to your particular product.

WARNINGS:

• FOR USE ONLY with 120 volt incandescent or halogen bulbs.
• DO NOT USE

with fluorescent bulbs, appliances, power supplies, low voltage lighting, or any other electrical devices.

• Transmitters

– Remote Control
– Add-A-Switch
– Entry Switch
– Indoor Wireless Motion Sensor
– Outdoor Wireless Motion Sensor

• Receivers

– Indoor Plug-In Converter
– Lamp Socket Converter
– Floodlight

This manual applies to the following products:

FEATURES

• Products are UL/cUL and/or FCC/IC tested and approved.
• Operational range of up to 100 feet.

Heath

®

/Zenith wireless lighting controls are designed to

work together. Simply determine which transmitter(s) you
would like to have control which receiver(s) and set the code

setting to match.

CODE SETTINGS

Note:

Most single system installations will not require any

change to the code setting. Transmitter(s) and receiver(s)
must have the same code and group setting to work together.
Switches 1 through 3 set the code. Switch 4 sets the Group
(A or B). See page 2 for switch locations.

DIM

ON

OFF

ON

OFF

DIM

Receiver(s)

Code

Transmitter(s)/

Receiver(s) Code

Group “A”

Group “B”

Remote Motion

Sensor Code

Group “A”

Example 1 - Code Settings, System 1

(Factory Setting)

Left Side Controls:

Controls One Set of

Group “A” or Group

“B” Receiver(s)

Right Side Controls:

Controls One Set of

Group “A” or Group

“B” Receiver(s)

Transmitter(s)/

Receiver(s) Code

Group “A”

Example 3 - Code Settings with Single Transmitter

When using a single group transmitter (

i.e.

Door Transmitter, Add-A-

Switch, Remote Motion Sensor) the code and group settings must
match receiver(s) for the system to function properly.

Note:

This setting will work independently of examples 1 and 2

because the code setting is different.

Note:

The code can also be changed to reduce interference problems

from other wireless products (

i.e.

wireless phones, garage door open-

ers, etc.). See

Troubleshooting Guide

for more information.

(

– Indicates Position of Switch)

Example 2 - Code Settings, System 2

Note:

When operating more than one system independently of each

other, set each system to a different code. There are 8 codes avail-
able by changing the settings of switches 1 through 3.

Receiver(s)

Code

Group “A”

Transmitter

Code

Group Switch
(Group “A” Selection Shown)

© 2007 HeathCo LLC

598-1116-10

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CODE SWITCH LOCATIONS; ON

2 598-1116-10 Indoor Plug-In Converter CODE SWITCH LOCATIONS ON 1 2 3 4 Code Switches 1 2 3 4 O N 2032 3V L ith ium Batte ry DIM Add-A-Switch Access Door 1 2 3 4 O N 2032 3V L ith ium Batte ry DIM Entry Switch Floodlight Lamp Socket Converter 1 2 3 4 Code Switches Screw Cover Code Switches Outdoor W...

Page 3 - ENGLISH; REmOTE CONTROL; Rear View of Remote Control; Code Settings; Left Side; Troubleshooting Guide

3 598-1116-10 ENGLISH Note: One remote control is able to independently oper- ate two receiver units. If more than two receiver units, operating independently, are desired, additional remote controls will need to be purchased.1. Remove Tab from Battery Chamber. Remove cover from back of transmitter....

Page 4 - Battery Replacement; Removing Battery Tab; Removing Access Door; Operation; Receiver

598-1116-10 5. Continue to press the DIM button until the desired dim level is reached. Note: Receiver remembers last DIM setting used. To recall last DIM setting, push and release the DIM button. Note: The DIM setting defaults to 50% in the event of a power failure. Important: Wait 1 to 2 seconds a...

Other Heath Zenith Models

All Heath Zenith Other