Heath Zenith 52-4474-4 - Manual
Heath Zenith 52-4474-4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – cautiOn: DO nOt connect the reD wire unless; Optional Wiring; Contact a qualified electrician if there
- Page 3 – recommended grounding Method; Black; black; white
- Page 4 – OptiOnaL Wiring; Wiring Diagram 1 – When wiring to control a standard light fixture:; Master; slave
- Page 5 – testing anD aDjustMents; Turn on the circuit breaker and light switch.; Adjustment of Coverage Area or Troubleshooting; Maximum Range; FinaL asseMBLy; Installation
- Page 6 – OperatiOn; Day; test; minutes; MODe sWitching suMMary; Flip light switch off for one; ManuaL MODe
- Page 7 – trOuBLeshOOting; If you experience a problem, follow this guide.; no service parts available for this product; syMptOM
- Page 8 – Dans certaines localités, le code de l’électricité exige; asseMBLage De La Lanterne; Lanterne cochère; instructions d'installation
- Page 9 – avertisseMent: ne pas raccorder le fil rOuge; Câblage Facultatif; Si vous
- Page 10 – Méthode de mise à la terre recommandée
- Page 11 – cÂBLage FacuLtatiF; Diagramme de câblage 1 – câblage d’un luminaire standard :; Maître; satellite
- Page 12 – essais et rÉgLages; Ré-enclenchez le disjoncteur puis ouvrez l’inter-; Réglage de; Portée maximale; asseMBLage FinaL
- Page 13 – FOnctiOnneMent; jour nuit; essai; Le moins sensible; Placer l’interrupteur ON-TIME à; rÉsuMÉ Du MODe De cOMMutatiOn; Mettre l’interrupteur hors; priOritÉ ManueLLe; PRIORITÉ MANUELLE; rÉgLage De La ZOne De cOuverture
- Page 14 – aucune pièce de rechange n’est disponible pour ce produit.; DÉpannage
Features
• Automatically comes on when motion is detected.
• Automatically turns light off.
• Photocell keeps the light off during daylight hours.
598-1286-01
unpacking
Be sure to remove all contents from packaging and verify
all items are present before assembling this light fixture.
This package includes the following items:
• Lantern (Includes: Top Cover, Glass Fixture, Fixture
Base)
• Universal mounting bracket (X-Bar)
• Mounting hardware
• Wire nuts
• Owner’s Manual
Before installation, record the model number listed
inside the fixture. attach receipt in case of possible
warranty issues.
Model number:
requireMents
• The Light Control requires 120 volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
•
Some electrical codes require installation by a qualified
electrician. Please check the codes in your area.
carriage Light with
Motion-activated
sensor
Lantern asseMBLy
1. Place glass fixture onto base assembly.
2. Line up the arrow on the bottom of glass fixture
with the arrow on the fixture base (see illustration
below).
Glass Fixture
Arrows
Fixture Base
Glass Fixture
Fixture Base
3. Gently push the two pieces together and rotate the
glass fixture 90° as shown below.
Models 52-4473-6
52-4474-4
installation and Operating
instructions
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1286-01 Wiring instaLLatiOn For best performance, mount the fixture about 6 feet (1.8 m) above the ground. 1. Remove two decorative nuts. 2. Remove X-Bar. 3. Tighten mounting screws on X-Bar finger tight. 4. Attach X-Bar to junction box. Junction Box X-Bar Decorative Nut Lantern Lantern Mounti...
3 598-1286-01 recommended grounding Method Use a green ground “pigtail” (not provided) and twist one end together with the bare fixture wire and the box ground wire. Secure with a wire connector. Secure the other end of the “pigtail” with the GND screw on the X-bar. Black to black White to white If ...
4 598-1286-01 Wiring Diagram 1 (Standard) Wiring Diagram 2 OptiOnaL Wiring This fixture is provided with a sensor rated for 360 Watts. Since the fixture is only rated 100 Watts, 260 Watts of additional lighting may be controlled by this sensor. When determining what a fixture is rated for, do not si...
