Heath Zenith 4193 - Manual
Heath Zenith 4193 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Twist the junction box wires and the; CAUTION: DO NOT connect the RED
- Page 3 – black wire. Connect all white wires; All wiring between fixtures should; Contact a qualified; This fixture is provided with a sensor rated; Master; If the dual; OPTIONAL WIRING
- Page 4 – COMPLETE THE INSTALLATION; 0 W bulbs in candelabra style.; Model 4193 Glass Installation
- Page 5 – TESTING; Turn on the circuit breaker and light; Least Sensitive; SPECIFICATIONS; Avoid aiming the control at:; Maximum Range; Switch the on-time to TEST position and
- Page 6 – TROUBLESHOOTING GUIDE; THREE YEAR LIMITED WARRANTY; TECHNICAL SERvICE; returning product to store.; No Service Parts Available for this Product
- Page 7 – LUZ DE ADORNO; FUNCIONAMIENTO; Características; MODO MANUAL; PRUEBA; Resumen de las modalidades del; AUTOMATICO; Prueba; Adorno
- Page 8 – Negro a negro; CUIDADO: NO conecte el cable ROJO; Luz de dos movimientos; Luz de un movimiento; ADvERTENCIA: Desconecte la energía
- Page 9 – Todo el cableado entre los aparatos; Maestra; La; CONEXION ALTERNA
- Page 10 – COMPLETE LA INSTALACION; Meta los cables en la caja de empalme.; de 60 vatios en estilo candelabro.; Después de completar la prueba de la; calafatee el aparato y la; Instalación del vidrio del Modelo; A igual que con cualquier clase de
- Page 11 – Alcance Máximo; Evite apuntar el control hacia:; Lo menos sensible
- Page 12 – GUIA DE INvESTIGACION DE AvERIAS; GARANTÍA LIMITADA A 3 AÑOS; SERvICIO TÉCNICO; antes de devolver el producto a la tienda.
- Page 13 – Caractéristiques; FONCTIONNEMENT; ESSAI; Résumé du mode de commutation
- Page 14 – INSTALLATION; A v E R T I S S E M E N T : C o u p e z; Une lanterne à détecteur de mouvement; AvERTISSEMENT: NE PAS raccorder le; Réglez la sensibilité; CÂBLAGE
- Page 15 – noir du luminaire standard. Raccordez; Maître; CÂBLAGE FACULTATIF
- Page 16 – COMPLÉTEZ L'INSTALLATION; Insérez les fils dans la boîte de jonction.; une ampoule de 100 W maxi-; Après avoir complété les essais de la page; calfeutrez la surface de montage; Installation des panneaux de
- Page 17 – ESSAIS; Éviter de pointer l’appareil:; Le moins sensible; FICHE TECHNIQUE
- Page 18 – GUIDE DE DÉPANNAGE; l’aide avant de retourner l’article au magasin.; Aucune pièce de rechange n’est disponible pour ce produit.
- Page 19 – GARANTIE LIMITÉE DE 3 ANS
Motion Sensing
Diecast Lantern
PF-4190 Series
Features
• Light comes on when motion is detected.
• Automatically turns light off.
• Dusk Accent lighting.
• Photocell keeps the light off during daylight
hours.
Requirements
• The Light Control requires 120 volts AC.
• If you want to use Manual Mode, the control
must be wired through a switch.
•
Some codes require installation by a
qualified electrician.
© 2006 DESA Specialty Products™
598-1167-03
OPERATION
* resets to Auto Mode at dawn.
Set the ON-TIME switch
on the bottom of the cover
plate to
TEST.
TEST 1 5 10 MIN
Set ON-TIME switch to 1,
5, or 10 minutes.
1 Second
OFF
then
...
Manual mode only works at
night because daylight re-
turns the sensor to AUTO.
Flip the light switch off for
one second then back on to
toggle between AUTO and
MANUAL MODE.
Manual mode works only with
the ON-TIME switch in the 1,
5, or 10 position.
... back on.
Mode Switching Summary
D
ual
B
rite
®
Dimmer Control
Light comes on half bright for selected time
after dusk (3 hr., 6 hr., until dawn). If motion
is sensed, the light turns on full bright for the
ON-TIME (1, 5, or 10 minutes) then returns
to dim mode.
This package includes:
• Lantern
• Easy to use universal mounting bracket
(X-Bar)
• Mounting hardware
• Wire nuts
ON-TIME Switch at 1,
5, or 10 minutes
Flip light switch
off for one second
then back on*
* If you get confused while switching modes,
turn the power off for one minute, then back
on. After the calibration time the control will
be in the AUTO mode.
MANUAL MODE
AUTO
TEST
Note:
When first turned on wait about 1
1
/
2
minutes for the circuitry to calibrate.
TEST
AUTO
MANUAL MODE
TEST
1 5 10 MIN
Before installation, record the model
number from back of fixture below.
Attach receipt in case of possible war-
ranty issues.
Mode:
On-Time
Works: Day Night
Test
5 Seconds
x
x
Auto
1, 5, or 10 Min
x
Manual
To Dawn*
x
Accent 3, 6 Hr, to Dawn
x
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1167-03 INSTALLATION For best performance, mount the fixture about 6 feet (1.8 m) above the ground. 1. Remove two nuts. 2. Remove X-Bar. Junction Box 5. Attach X-Bar to junction box Due to the size and weight of the fixture, you may find it helpful to have an assistant hold the fixture in plac...
3 598-1167-03 Wiring to Motion Light & Standard Fixture BLACK WHITE BLACK (Standard) ❒ When wiring to additional standard fixture only: Strip the motion sensor’s red wire and connect to the standard light’s black wire. Connect all white wires together. Total fixture ratings must not exceed 360 W...
4 598-1167-03 COMPLETE THE INSTALLATION ❒ Stuff the wires into the junction box. Make sure none of the wires get pinched. Slide the fixture onto the mounting screws and tighten nuts. ❒ Install one 100 W max. light bulb, or three 60 W bulbs in candelabra style. ❒ Install the fixture top. Secure with ...
