Transition Networks SCSCF30XX-10X - Manual
Transition Networks SCSCF30XX-10X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Set the Loop-Back Switch; Installation; Set the Configuration Switches
- Page 3 – Set the Coax Grounding Jumpers; (located on the circuit board near the coax ports); Install the Coax Cable
- Page 4 – Power the Device; AC; Cable Specifications; Coax Cable; Peak pulse power in DBm; Fiber Cable
- Page 6 – Declaration of Conformity
- Page 7 – Compliance Information; FCC Regulations
* Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Part Number
Port One - Copper
Port Two - Duplex Fiber-Optic
SCSCF3011-100
75 ohm coax (BNC)
ST, 1300 nm multimode
2 km
(1.2 miles)*
SCSCF3013-100
75 ohm coax (BNC)
SC, 1300 nm multimode
2 km (
1.2 miles)*
SCSCF3014-100
75 ohm coax (BNC)
SC, 1310 nm singlemode
20 km
(12.4 miles)*
SCSCF3015-100
75 ohm coax (BNC)
SC, 1310 nm singlemode
40 km
(24.8 miles)*
SCSCF3016-100
75 ohm coax (BNC)
SC, 1310 nm singlemode
60 km
(37.3 miles)*
SCSCF3017-100
75 ohm coax (BNC)
SC, 1550 nm singlemode
80 km
(49.7 miles)*
SCSCF3018-100
75 ohm coax (BNC)
MT-RJ, 1300 nm multimode
2 km
(1.2 miles)*
SCSCF3019-100
75 ohm coax (BNC)
LC, 1310 nm single mode
20 km
(12.4 miles)*
SCSCF3029-100
75 ohm coax (BNC)
SC, 1310 mn (TX)/1550 nm (RX)
20 km
(12.4 miles)*
SCSCF3029-101
75 ohm coax (BNC)
SC, 1550 mn (TX)/1310 nm (RX)
20 km
(12.4 miles)*
SCSCF3029-100
and
-101
are intended to be installed in the same network where
one is the local converter and the other is the remote converter.
User’s Guide
SCSCF30xx-10x
Stand-Alone Device
•
DS3 or T3 / E3
•
Coax (BNC) to Fiber
Transition Networks SCSCF30xx-10x series
Devices encode and decode DS3 or E3 coax
copper signals over fiber optic cable to extend
the distance and transmission reliability of high-
speed DS3 or E3 data traffic. The SCSCF30xx-
10x also connects remote locations via T3/E3
cable.
Note:
The CCSCF30xx-10x model is the
chassis version of the Device. For more
information, see the CCSCF30xx-10x user’s
guide on-line at www.transition.com.
Installation . . . . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . . . . .6
Cable Specifications . . . . . . . . . . . . . .7
Technical Specifications . . . . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . . . . .9
Compliance Information . . . . . . . . .12
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Part Number Port One - Copper Port Two - Single Fiber Optic SCSCF3029-102 and -103 are intended to be installed in the same network whereone is the local converter and the other is the remote converter. *Ty...
4 SCSCF30xx-10x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge precautionswhen setting the jumper. Failure to observe this caution could result in damage to, andsubsequent fa...
SCSCF30xx-10x 6 Operation After installation, the Device should function without operator intervention. Use thestatus LEDs to monitor the Device operation in the network. SDC Green on The coax link is up. Green flashing The coax link is in loop-back mode. Yellow on AIS (Alarm Indication Signal) on t...
