Transition Networks CPSMP-130 - Manual
Transition Networks CPSMP-130 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – The Power Supply Module in the 13-Slot Chassis; a n y; Install the Power Supply Module; provided the module to be installed
- Page 3 – Connect to External Power; Continued; NOT
- Page 4 – Replace the Power Supply Module; provided the module to be replaced has been
- Page 5 – Replace the Fuse; provided the module to be serviced has been; size and rating
- Page 6 – Technical Specification; Contact Us; Troubleshooting; YES
- Page 7 – Compliance Information
User’s Guide
CPSMP-130
48-VDC Power Supply Module
CPSMP-140
24-VDC Power Supply Module
13-Slot PointSystem™ Accessory
The Transition Networks
CPSMP-130
power supply is a 48-VDC slide-in-module
t h a t p r o v i d e s o p t i o n a l , r e d u n d a n t p o w e r t o t h e C P S M C 1 3 1 0 - 1 0 0 1 3 - s l o t
PointSystem™
chassis and any installed media converter slide-in-modules and
management modules.
The Transition Networks
CPSMP-140
power supply is a 24-VDC slide-in-module
t h a t p r o v i d e s o p t i o n a l , r e d u n d a n t p o w e r t o t h e C P S M C 1 3 2 0 - 1 0 0 1 3 - s l o t
PointSystem™
chassis and any installed media converter slide-in-modules and
management modules.
The figure below illustrates the components of both types of power supplies:
•
An
On/Off switch
that, when set to
“I”
, allows the power supply module
to supply power to the chassis, and any installed modules.
•
A
panel fastener screw
that secures the power supply module to the
chassis.
•
A
power LED
indicator.
•
A
handle
for installing and removing the power supply module to/from
the chassis.
•
A
fuse
installed on the circuit board inside the power supply module’s
housing.
•
A set of three (3)
external power connectors
that distribute power from an
e x t e r n a l D C o u t l e t t o a c h a s s i s g r o u n d c o n n e c t o r , a p o s i t i v e ( + )
connector, and a negative (-) connector on the power supply module.
I
0
-
+
+
+
+
+
Power LED
External Power Connectors
On/Off Switch
Fuse
(on the circuit board
I
0
-
+
Panel Fastener Screw
Handle
Install the Power Supply Module . . . . .3
Connect to External Power . . . . . . . . .4
Replace the Power Supply Module . . .6
Replace the Fuse . . . . . . . . . . . . . . . . .8
Technical Specifications . . . . . . . . . .10
Troubleshooting . . . . . . . . . . . . . . . .11
Contact Us . . . . . . . . . . . . . . . . . . . .11
Compliance Information . . . . . . . . . .12
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CPSMP-130 & CPSMP-140 2 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 READ AND FOLLOW ALL WARNING NOTICES & INSTRUCTIONS MARKED ONTHE PRODUCT OR INCLUDED IN THE MANUAL. CAUTION: All installation and service must be performed by qualified servicepersonnel. CAUT...
CPSMP-130 & CPSMP-140 4 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Connect to External Power CAUTION: Ensure that external power source is NOT powered and that theOn/Off switch on the power supply module is set to “0” when connecting tothe external power source...
CPSMP-130 & CPSMP-140 6 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 WARNING: Do NOT connect the power supply module to the external powersource before installing it into the chassis. Failure to observe this caution couldresult in equipment damage and/or personal...
