Transition Networks C4TEF10XX-10X - Manual
Transition Networks C4TEF10XX-10X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Part Number; Copper and Fiber Ports; Installation; Configuration Switches; serial options
- Page 3 – switch 5; odd; even; switch 4
- Page 4 – not in use; Hardware/Software Jumper; Hardware; Power the Media Converter
- Page 5 – Install the T1/E1 Cable; Install the Fiber Cable
- Page 6 – Fiber Network LEDs; Operation; Remote Management Function; SNMP
- Page 7 – Cable Specifications; Fiber Cable
- Page 8 – Technical Specifications; Optional Accessories; Troubleshooting; YES
- Page 9 – Is data transfer failing on the fiber port?
- Page 10 – Contact Us; Compliance Information
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network.
T h e
c h a s s i s v e r s i o n
o f t h e m e d i a
converter is
C4TEF10xx-10x
. For more
information, see the user’s guide on-line
at: www.transition.com.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . .10
Cable Specifications . . . . . . . . . .12
Technical Specifications . . . . . . .14
Troubleshooting . . . . . . . . . . . . .15
Compliance Information . . . . . . .19
User’s Guide
S4TEF10xx-10x
Stand-Alone Media Converter
• RS-232 to Fiber
• (4) T1/E1 to Fiber
The S4TEF10xx-10x media converter can
extend signals from an RS-232 data port and
up to four (4) T1/E1 network ports over fiber.
The RS-232 and T1/E1 interfaces are independent of each other and the signals
from these ports can be sent over the fiber interface simultaneously.
The S4TEF10xx-10x is designed to be installed in pairs. For example, install one
S4TEF1011-100 as the local media converter and another S4TEF1011-100 as the
remote media converter.
All S4TEF10xx-10x models have the following copper connectors:
The various fiber connectors are available on separate models. Both duplex and
single mode fiber optic converters are available:
Part Number
Duplex Fiber-Optic -
100Base-FX
S4TEF1011-100
ST, 1300 nm multimode, 2 km (1.2 miles)*
S4TEF1013-100
SC, 1300 nm multimode, 2 km (1.2 miles)*
S4TEF1014-100
SC, 1310 nm single mode, 20 km (12.4 miles)*
S4TEF1015-100
SC, 1310 nm single mode, 40 km (24.8 miles)*
S4TEF1016-100
SC, 1310 nm single mode, 60 km (37.2 miles)*
S4TEF1017-100
SC, 1550 nm single mode, 80 km (49.7 miles)*
S4TEF1018-100
MT-RJ, 1300 nm multimode, 2 km (1.2 miles)*
Connector Type
Number
Description
RS-232
one (1)
6-pin, DIN serial, 3.2 m (10 ft.)*
T1/E1
four (4)
RJ-48
S4TEF1029-10x
(single mode, single fiber models are listed on page 2)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NOTE: An RS-232 cable with a 6-pin DIN connector and a DB-9 connector is included with the S4TEF10xx-10x media converter. 2 S4TEF10xx-10x 24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 PWR LKF 100Base-FX TX RX 4 3 2 1 LNK LNK LNK LNK AIS AIS AIS AIS fiber port T1/E1 ports...
4 S4TEF10xx-10x 24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Switch Set #1 - T1/E1 Options 5, 6, 7, 8 - Loop-Back Settings The loop-back setting is used for installation and network debugging procedures.Each of the T1/E1 ports can be individual...
6 S4TEF10xx-10x 24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Switch Set #2 - Serial Options 6 - not in use 7 - not in use 8 - not in use 9 - not in use switches 6, 7, 8, & 9 are not in use 9 8 7 6 10 - Fiber Loop-Back up - Disabled fiber lo...
