Transition Networks DVP 5960 - Manual
Transition Networks DVP 5960 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FIBER CABLE; Straight Through Cable
- Page 3 – TROUBLESHOOTING SUGGESTIONS; YES; UTP to Twinax Connector:
- Page 4 – Multimode up to 2 kilometers; and; the Twinax connector at the back of a; MEDIA CONVERTERS in the NETWORK
MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Host Connection
IBM® S/3x (System 34, 36, 38) host, AS/400™
host or 5x94 remote controller
Case dimensions
4.75" x 3.0" x 1.0"
(119mm x 76mm x 25mm)
Shipping Weight
2 pounds
(0.9 kilograms)
Environment
Temperature:
0-50°C (32-122°F)
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Five years
Power Supply Requirements
Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 0.5 A).
TN PN
Requirement
Location
3525
240 volts, 50 hertz
United Kingdom
3525
230 volts, 50 hertz
Europe
3518
120 volts, 60 hertz
USA/Canada/Mexico
3514
100 volts, 50-60 hertz
Japan
3525
240 volts, 50 hertz
Australia
NOTE: This product also can be powered by the Transition Networks E-MCR series media
converter rack.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Copyright Restrictions
© 1998 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
33060.A
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
The TRANSITION Networks 5250 Copper to Fiber PS-CF-01 series media
converters, designed to support all IBM
®
5250 compliant devices (including
devices operating at a non-standard rates), extends the signal distance of an
AS/400™ or S/3x host computer or a 5x94 remote controller to terminal
equipment over twisted-pair copper and over multimode or singlemode fiber.
PS-CF-01 series media converters allow twisted-pair copper network
extension distances up to 1524 meters (762 meters each connection on
two media converters) AND fiber network extension distances up to 2
kilometers on multimode fiber and up to 8 kilometers on singlemode
fiber.*
STATUS LEDS
Power
Steady green LED
indicates connection
to external AC power.
UTP/STP Blinking green LED
indicates network traffic on unshielded or shielded twisted-pair
link.
Fiber
Blinking green LED indicates network traffic on fiber link.
Minneapolis, MN 55344 USA
5250 Copper/Fiber
Media Converter
PS-CF-01, PS-CF-01(SC), PS-CF-01(SM)
USER’S GUIDE
10BASE-T
RX
TX
Fiber
UTP/STP
Power
PS-CF-01
Provides an RJ-45 twisted-pair
connector to copper cable and a
set of RX (receive) and TX
(transmit) ST connectors to
multimode fiber-optic cable.
PS-CF-01(SC)
Provides an RJ-45 twisted-pair
connector to copper cable and an
RX (receive) and TX (transmit) SC
connector to multimode fiber-optic
cable.
PS-CF-01(SM)
Provides an RJ-45 twisted-pair
connector to copper cable and an
RX (receive) ST and TX (transmit)
SC connector to singlemode fiber-
optic cable.
PS-CF-01
*See note at top of pages 4 & 5.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Installation NOTES To install the PS-CF-01 series media converter: 1. Connect host signal to PS-CF-01 media converter. • Locate or build twisted-pair cables that are compliant with cable specifications (See page 7) and with male RJ-45 plug connectors installed at both cable ends. NOTE: Install TRANS...
TROUBLESHOOTING SUGGESTIONS If a Media Converter fails, ask the following questions: 1. Is the Power LED on the media converter illuminated? NO • Is the power adapter the proper voltage and cycle frequencyfor the AC outlet? NOTE: Refer to the “Power SupplyRequirements” on the back page. • Is the pow...
AS/400 S/3x or 5x94 UTP/STP Fiber PowerStar ™ III PowerStar ™ IV UTP/STP Fiber PowerStar ™ IV UTP/STP Fiber RJ-45 copper connection at PowerStar ™ III or PowerStar ™ IV front TX/RX connection to fiber SIC at PowerStar ™ IV back PowerStar ™ RJ-45 copper/balun connection to Twinax connector at PowerSt...
