Transition Networks CETTF10XX-105 - Manual
Transition Networks CETTF10XX-105 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Failure to observe this caution could result in; Set the 4-Position Switch; Hardware; Installation; Failure to observe this caution could result in damage to, and; Connect the Twisted-Pair Copper Cable
- Page 3 – Connect the fber cable; PointSystemTM; Operation; Status LEDs; PWR; SNMP; FocalPointTM
- Page 4 – Product Features; AutoCross; Factory default is “enable AutoCross.” Transition networks; Link Pass Through; Cable Specifications; Fiber Cable
- Page 5 – Copper Cable; Technical Specifications
- Page 6 – Troubleshooting; Contact Us
- Page 7 – Compliance Information
User’s Guide
CETTF10xx-105
Slide-in-Module Media Converter
• Ethernet
• Copper to Fiber
• 10Base-T to 10Base-FL
Transition Networks CETTF10xx-105 series Ethernet
10Base-T to 10Base-FL media converters (designed
to be installed in a
PointSystem™
chassis) connect
10Base-T twisted-pair copper cable to multimode or
single mode 10Base-FL fiber-optic cable.
*
CETTF1029-105
and
CETTF1029-106
are designed to be installed in the same
network where one is the local converter and the other is the remote converter.
The distances listed are the typical maximum cable distance. Actual distance is
dependent upon the physical characteristics of the network installation.
Part Number
Port One -
Copper
10Base-T
Port Two -
Fiber-Optic
10Base-FL
CETTF1011-105
RJ-45
100 m (328 ft)*
ST, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1012-105
RJ-45
100 m (328 ft)*
ST, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1013-105
RJ-45
100 m (328 ft)*
SC, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1014-105
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1022-105
RJ-45
100 m (328 ft)*
ST, 1310 nm single mode, duplex
40 km (24.9 miles)
CETTF1027-105
RJ-45
100 m (328 ft)*
ST, 1300 nm multimode, duplex
5 km (3.1 miles)
CETTF1018-105
RJ-45
100 m (328 ft)*
MT-RJ, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1014-106
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1015-105
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
40 km (24.9 miles)
CETTF1029-105*
RJ-45
100 m (328 ft)*
SC, 1310 nm (TX) / 1550 nm (RX)
single fiber, 20 km (12.4 miles)
CETTF1029-106*
RJ-45
100 m (328 ft)*
SC, 1550 nm (TX) / 1310 nm (RX)
single fiber, 20 km (12.4 miles)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Installation CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the 4-position switch and the jumper and wheninstalling the media converter. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter. Set the 4...
CETTF10xx-105 4 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued Connect the fber cable 1. Locate or build IEEE 803.2 ™ compliant 10Base-FL fiber cable with male, two-stranded TX to RX connectors installed at both ends. 2. Connect the fiber cabl...
CETTF10xx-105 6 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Operation -- Continued Product Features AutoCross ™ When the AutoCross feature is activated, it allows either straight-through(MDI) or crossover (MDI-X) copper cables to be used when connecting to10Base-T d...
