Husqvarna HUV 4213-G - Manual

Table of Contents:

• Page 3 – NOTICE
• Page 4 – FOREWORD
• Page 5 – TABLE OF CONTENTS
• Page 6 – Vehicle Feature Identification
• Page 10 – PROPOSITION 65 - STATE OF CALIFORNIA; WARNING; Rotating Parts; Practice Safety; compared with the reality of severe personal injury.
• Page 11 – Safety Details; SAFETY DETAILS; result in minor personal injury or product or property damage.; CAUT ION; could result in property damage.; Figure 1 Battery Cable Removal
• Page 12 – General Warnings; GENERAL WARNINGS; DAN G E R
• Page 13 – Model Identification; shield and rubber gloves when working on or near batteries.; MODEL IDENTIFICATION; . There is also a second serial number
• Page 14 – Controls and Indicators; CONTROLS AND INDICATORS; See General Warnings on page 10.; and operating procedures.; KEY SWITCH; Figure 3 Key Switch
• Page 15 – damage to the unitized transaxle.; FORWARD/REVERSE CONTROL; The Forward/Reverse handle is located on the seat support panel; See WARNING and CAUTION on; Husqvarna; ACCELERATOR PEDAL; to the original position and the engine will idle.; See WARNING and CAUTION on page 12.; Figure 4 Forward/Reverse Handle
• Page 16 – BRAKE PEDAL; the vehicle, press the brake pedal; PARK BRAKE; See; vehicle from rolling.; CHOKE; Figure 5 Accelerator and Brake Pedal
• Page 17 – DIFFERENTIAL LOCK; • Disengage differential lock on paved surfaces.; LOW OIL WARNING LAMP; . If the warning lamp comes on, oil should be checked and added; See following CAUTION.; permanent engine damage.; FUEL GAUGE/HOUR METER; odic Service Schedule on page 26.; Figure 9 Low Oil Warning Lamp
• Page 18 – Seat Latch and Adjustment; HEADLAMP CONTROL; SEAT LATCH AND ADJUSTMENT; See following WARNING.; PRE-OPERATION AND DAILY SAFETY CHECKLIST; Each Husqvarna; • Safety and information decals:; should be fully charged.; See Engine Oil on page 29.
• Page 19 – Performance Inspection; See Fueling Instructions on page 33.; fuel filters, and carburetor for fuel leakage on a daily basis.; See Master Cylinder on page 29.; PERFORMANCE INSPECTION; Check for proper operation.; See Controls and Indicators on page 12.; in the REVERSE position.; • Differential lock cable:; mance. Have a Husqvarna
• Page 20 – Driving Instructions; DRIVING INSTRUCTIONS
• Page 21 – STARTING THE VEHICLE; Make sure the Forward/Reverse handle is in the NEUTRAL position.; • Operator must control vehicle speed when going downhill.; STOPPING THE VEHICLE; See following WARNING and CAUTION; pedal to hold position.
• Page 22 – Bed Latch and Prop Rod; PARKING AND LEAVING THE VEHICLE; the vehicle from rolling.; See also Figure 24 on page 34.; BED LATCH AND PROP ROD; The bed latch; resulting in severe personal injury or death.; equipped with the electric bed lift accessory.
• Page 23 – Front Shock Absorbers; FRONT SHOCK ABSORBERS
• Page 24 – Towing with the Vehicle; TOWING WITH THE VEHICLE; TRANSPORTING ON A TRAILER; per vehicle being transported.
• Page 25 – Storage; STORAGE; • Keep gasoline out of the reach of children.; Frozen batteries can explode.; • Batteries in a low state of charge will freeze at low temperatures.; PREPARING THE VEHICLE FOR EXTENDED STORAGE; Tilt the bed and ensure that the prop rod is properly engaged.
• Page 26 – See WARNING “To avoid unintentionally start-; Adjust tires to recommended tire pressure.; See Vehicle Specifications on page 38.; Perform semiannual periodic lubrication.; See Periodic Lubrication Schedule on page 28.; RETURNING THE STORED VEHICLE TO SERVICE; Tilt the bed and ensure that the prop rod is properly engaged.; See WARNING “For vehicles with cargo; Figure 12 Fuel Shut-off Valve – Closed Position; OFF; VIEWED FROM SELECTOR
• Page 27 – MAINTENANCE; Contact your local Husqvarna; See following; Figure 13 Fuel Shut-off Valve – Open Position
• Page 28 – Periodic Service Schedule; the NEUTRAL position and chock the wheels prior to servicing.; PERIODIC SERVICE SCHEDULE; maintenance and service manual.
• Page 29 – REGULAR INTERVAL
• Page 30 – Periodic Lubrication Schedule; PERIODIC LUBRICATION SCHEDULE
• Page 31 – Master Cylinder; MASTER CYLINDER; Raise or remove the seat to check the brake fluid level.; BRAKE FLUID; ENGINE OIL; ENGINE OIL LEVEL CHECK; • Do not remove dipstick while engine is running.; Figure 16 Brake Fluid Reservoir
• Page 32 – Engine Oil; ENGINE OIL AND FILTER CHANGE; NEUTRAL position. Chock the front wheels.; engine oil to drain into the pan.; gloves when handling oil drain plug, oil filter, and oil drain pan.; sion washer remains on the drain plug.
• Page 35 – Fueling Instructions; OIL VISCOSITY; more frequently when using them.; FUELING INSTRUCTIONS; • Turn the key switch to the OFF position before fueling.; Remove fuel cap and fill tank with fresh unleaded gasoline only.; See preceding DANGER and CAU-; Figure 23 Oil Viscosity Chart
• Page 36 – BATTERY; • Follow all instructions carefully when working with batteries.
• Page 37 – Battery; The battery in a Husqvarna; Figure 25 Battery
• Page 38 – Cleaning the Vehicle; CLEANING THE VEHICLE; protect occupants from flying objects.
• Page 39 – Subsequent Owner Registration; ELECTRIC WINCH ACCESSORY; See Vehicle Feature Identification on beginning page 4.; • Before beginning a winch operation:; SUBSEQUENT OWNER REGISTRATION
• Page 40 – Vehicle Specifications; VEHICLE SPECIFICATIONS; SPECIFICATIONS
• Page 44 – CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
• Page 45 – FUEL AND OIL RECOMMENDATIONS; EMISSION CONTROL INFORMATION; CAUTION