Heath Zenith SL-5330 - Manual
Heath Zenith SL-5330 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Wall Mount
- Page 3 – TEST AND ADJUSTMENT; Bottom of Sensor; SPECIFICATIONS
- Page 4 – TROUBLESHOOTING GUIDE; TEN YEAR LIMITED WARRANTY; TECHNICAL SERVICE; No Service Parts Available for this Product
OPERATION
Model SL-5330
Motion Sensor
Light Control with
Protective Lamp
Shields
© 2003 DESA Specialty Products™
598-1131-01
* resets to Auto Mode at dawn.
TEST
Light Control
Sensor
Cover
Plate
Lamp Holders
6 Screws
(3 sizes included)
Gasket
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight hours.
This package includes:
Requirements
• The Light Control requires 120-volts AC.
• If you want to use the Manual Mode, the control must
be wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
TEST 1 5 20
ON-TIME
Put ON-TIME switch on the sensor
bottom to TEST.
MANUAL MODE
ON-TIME
TEST 1 5 20
... back on.
AUTO
1 Second OFF
then...
Put the ON-TIME switch in the 1, 5
or 20 minute position.
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Mounting Bolt
Mounting Strap
Rubber Plug
Plastic Hanger
2 PAR Lamps
2 Wire
Connectors
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Auto
1, 5, 20 min.
x
Manual
Until Dawn*
x
Move ON-TIME Switch to
1, 5 or 20 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the
calibration time the control will be in the AUTO mode.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1131-01 INSTALLATION For easy installation, select an existing light with a wallswitch for replacement. W IRE THE L IGHT C ONTROL . ❒ Turn power off at the fuse or circuit breaker. ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using twoscrews that fit your junction...
3 598-1131-01 Motion Motion TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 1 / 2 minute calibration period before it will detect motion. When first turned on wait 1 1 / 2 minutes. Bottom of Sensor Avoid aiming the sensor at: • Objects that change temperature...
4 598-1131-01 TROUBLESHOOTING GUIDE SYMPTOM Lights will not comeon. L i g h t s c o m e o nin daylight. Lights come on forno apparent rea-son. POSSIBLE CAUSE 1. Light switch is turned off.2. F l o o d l i g h t i s l o o s e o r burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Dayli...
