Heath Zenith SH-5407 - Manual
Heath Zenith SH-5407 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; TEST AND ADJUSTMENT
- Page 3 – Bottom of Sensor; SPECIFICATIONS
- Page 4 – TROUBLESHOOTING GUIDE; TECHNICAL SERVICE; before returning product to store.; No Service Parts Available for this Product
- Page 5 – • LED indica que se ha detectado movimiento; FUNCIONAMIENTO; Mueva el interruptor de; Resumen de las modalidades del; Cuando lo prenda por primera vez espere unos 1; PRUEBA; Tiempo de; Prueba; segundos; Manual
- Page 7 – Parte de abajo del detector; ESPECIFICACIONES
- Page 8 – GUIA DE INVESTIGACION DE AVERIAS; SERVICIO TÉCNICO; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.
Replacement
Motion Sensor
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must
be wired through a switch.
•
Some codes require installation by a qualifi ed
electrician.
© 2007 HeathCo LLC
598-1155-01
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Photocell keeps the lighting off during daylight
hours.
• LED indicates motion was sensed (day or
night).
Model SH-5407
OPERATION
Move ON-TIME Switch
to 1, 5, or 10 minutes
Mode Switching Summary
Flip switch off for
one second then
back on*
* resets to Auto Mode at dawn.
TEST
AUTO
MANUAL MODE
ON-TIME
ON-TIME
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the
calibration time (1
1
/
2
min.) the control will be in the
AUTO mode.
10 5 1
TEST
10 5 1
TEST
MANUAL MODE
AUTO
TEST
... back on.
1 Second OFF
then
...
Manual mode only works at night
because daylight returns the sen-
sor to AUTO.
Flip the light switch off for one
second then back on to toggle
between AUTO and MANUAL
MODE.
Manual mode works only with
the ON-TIME switch in the 1, 5,
or 10 position.
Note:
When fi rst turned on wait about 1
1
/
2
minutes
for the circuitry to calibrate.
Put the ON-TIME switch in the 1,
5, or 10 minute position.
Put the ON-TIME switch on the
bottom of the sensor in the TEST
position.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Normal
1, 5, 10 min.
x
Manual
Until Dawn*
x
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- 598-1155-01 ❒ Swing the sensor head towards the clamp screw. For eave mount only: Controls INSTALLATION ❒ Remove the existing light fi xture, if present. These instructions show the sensor wired to fl ood-lamps. The white sensor wire is neutral. The black sensor wire is hot. The red wire is the ...
-3- 598-1155-01 Motion Least Sensitive Most Sensitive Sensor Motion The sensor is less sensitive to motion directly to-wards it, most sensitive to motion across its fi eld of view. Maximum Range Maximum Coverage Angle 8 ft. (2.4m) 70 ft. (21m) RANGE 10 5 1 TEST ON-TIME Bottom of Sensor Avoid aiming ...
-4- 598-1155-01 TROUBLESHOOTING GUIDE SYMPTOM L i g h t s w i l l n o t come on. Lights come on in daylight. Lights come on for no apparent reason. POSSIBLE CAUSE 1. Light switch is turned off.2. Light is loose or burned out.3. Fuse is blown or circuit breaker is turned off. 4. Daylight turn-off is ...
