Heath Zenith 598-1227-01 - Manual

Heath Zenith 598-1227-01

Heath Zenith 598-1227-01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – Set the push button jumpers to match the
  • Page 3 – Code and Tune Settings; Code Settings; The jumper positions 1 through 7 are used for setting the code.
  • Page 4 – Tune Settings
  • Page 5 – Replacing Push Button Batteries
  • Page 6 – Troubleshooting; Chime does not sound:; • Make sure push button and chime codes are the same (See pages ,; Batteries seem OK, but the chime does not work when installed:; • Do not mount chime or push button on metal or near metal studs. This
  • Page 7 – for assistance before returning product to store.; assistance at; No Service Parts Available for this Product
  • Page 8 – FIVE YEAR LIMITED WARRANTY; ACE
  • Page 9 – Característica barra de empuje iluminada; Este pulsador inalámbrico ACE
  • Page 10 – Fije los puentes del pulsador de acuerdo al código del receptor
  • Page 11 – Programaciones del código y del tono; Programaciones del código
  • Page 12 – Programación del tono; Su campana inalámbrica ACE
  • Page 13 – Reemplazo de las baterías del pulsador; Coloque las baterías con el lado
  • Page 14 – Análisis de Averías; • Asegúrese que los códigos del pulsador y de la campana sean los
  • Page 15 – Servicio Técnico; inglés) para pedir ayuda antes de devolver el producto a la; Si el problema continúa, llame; No hay piezas de servicio disponibles para este producto.; Información Regulatoria
  • Page 16 – GARANTÍA LIMITADA A 5 AÑOS
  • Page 17 – Bouton-poussoir illuminé
  • Page 19 – Réglages du code et de la mélodie; Réglage du code
  • Page 20 – Réglage de la mélodie
  • Page 21 – Remplacement des piles de l'unité de bouton-poussoir
  • Page 22 – Dépannage; Le carillon ne sonne pas:; le carillon des planchers.
  • Page 23 – Service Technique; ment) pour obtenir de l’aide avant de retourner l’article au; le; Aucune pièce de rechange n’est disponible pour ce produit.; Renseignements de règlements
  • Page 24 – GARANTIE LIMITÉE DE 5 ANS
Loading the manual

Lighted Wireless
Push Button Accessory

The ACE

®

Wireless Push Button Accessory works with existing ACE

®

jumper or dip switch systems.
• Battery powered push button - No wires to run.
• 128 selectable codes allow more than one chime system in the same

house.

• LED lighted push bar (see Lighted Push Bar Feature).

© 2007

598-1227-01

(Style may vary from illustration)

Lighted Push Bar Feature

This ACE

®

wireless push button contains a LED (Light Emitting Diode) that

will illuminate in dark conditions so the push button will be more visible for
your guests. This (patent pending) technology and built-in photocontrol
will allow the light intensity of the push button LED to increase as the
outdoor light conditions around the push button decreases. The actual time
and intensity that the LED is visible will depend on the specific mounting
environment of the push button. In nominal conditions the batteries will
typically last 2 years.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Set the push button jumpers to match the

-2- 598-1227-01 1. Install two lithium type CR2032 3 volt bat-teries (included). Remove back of case by pushing in tab on bottom with a small screw-driver. Make sure battery is oriented properly (see page 5). 2. Set the push button jumpers to match the chime receiver code. See “Code and Tune Setting...

Page 3 - Code and Tune Settings; Code Settings; The jumper positions 1 through 7 are used for setting the code.

-- 598-1227-01 Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button.WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The push ...

Page 4 - Tune Settings

-4- 598-1227-01 Tune Settings Your ACE ® wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by follo...

Other Heath Zenith Models

All Heath Zenith Other