Heath Zenith 598-1119-07 - Manual
Heath Zenith 598-1119-07 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IndOOr Plug-In reCeIver; IndOOr/OutdOOr reCeIver; Operation
- Page 3 – Channel settIngs; the channel is factory set. most instal-; Switch; dIP sWItCh lOCatIOns
- Page 4 – returning product to store.; no service Parts available for these Products
- Page 5 – One year lImIted Warranty
- Page 6 – CaraCterÍstICas; Productos a control remoto; Operación; COntrOl remOtO de 2 BOtOnes
- Page 7 – reCePtOr Para InterIOres /
- Page 8 – CalIBraCIOnes del Canal; el canal viene calibrado de fábrica. la; Las; uBICaCIOnes de lOs
- Page 9 – antes de devolver el producto a la tienda.; no hay piezas de servicio disponibles para este producto
- Page 10 – InFOrmaCIÓn regulatOrIa; garantÍa lImItada a 1 aÑO
- Page 11 – CaraCtÉrIstIQues; Produits télécommandés; Fonctionnement; tÉlÉCOmmande À deuX BOutOns
- Page 12 – eXtÉrIeur
- Page 13 – rÉglage des vOIes; les voies sont réglées à l’usine. dans; commande et du récepteur.; emPlaCement des
- Page 14 – l’aide avant de retourner l’article au magasin.; aucune pièce de rechange n’est disponible pour ce produit
- Page 15 – renseIgnements de règlements; garantIe lImItÉe de 1 an
- Page 16 – Fecha de compra / date d’achat
© 2007 HeathCo LLC
598-1119-07
Features
• Quickly add ON/OFF control of a receptacle without the expense of new wiring.
• Four selectable channels allowing the use of up to four separate systems in the same home.
• Products are UL/cUL and/or FCC/IC tested and approved.
• Operational range of up to 50 feet.
remote Controlled Products
Operation
1. The two buttons on the remote will
operate one or more receiver units
with matching channels.
Note:
Receivers must be at least 10
feet apart for best performance.
2. Push the ON button to turn the
plugged in receiver on or the
OFF button to turn the plugged in
receiver off.
Battery replacement
The remote control requires a type A23 12 Volt
alkaline battery to operate. The remote control
is shipped with the battery installed. With typical
use, the battery will last approximately one year.
Remove battery when remote will not be used
for an extended period of time.
To replace the battery, follow the instructions
below:
1. Place remote control face down on a flat
surface.
2. Remove screw on bottom of remote with a
small phillips-head screwdriver.
2-ButtOn remOte COntrOl
ON
OFF
3. Gently insert a small flat-head screwdriver
between the two halves on the bottom of the
remote and twist. Carefully separate the back
of the remote from the front.
4. Lift the back of the remote up and lay aside.
5. Remove battery. Install replacement battery.
Make sure battery is oriented properly (see
illustration).
6. Reassemble remote in reverse order.
Inside of Remote Control
ON
12 V
1 2
Battery
Compartment
(Type A23)
Removing Back of Remote Control
Flat-Head
Screwdriver
Philips-Head
Screw
Remote
Control Back
ON
OFF
This manual applies to the following products:
2-Button Remote Control
Indoor Plug-In Receiver
Indoor/Outdoor Receiver
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1119-07 IndOOr Plug-In reCeIver Features and Ratings:• Up to 500 Watt maximum incan- descent load. • Up to 300 Watt maximum fluo- rescent load. • Up to 400 Watt maximum TV load. • Up to 1/3 Hp maximum motor load.• No wiring required. Operation Note: When using two or more receivers, the receiv...
3 598-1119-07 Channel settIngs Note: the channel is factory set. most instal- lations will not require you to change the two dip switches on your remote control or receiver. Note: If purchasing more than one remote control system, select different operating channels unless you want one remote contro...
4 598-1119-07 regulatOry InFOrmatIOn This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including inter...
