Heath Zenith 52-4041-4 - Manual
Heath Zenith 52-4041-4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Wall Mount
- Page 3 – TEST AND ADJUSTMENT; SPECIFICATIONS; Bottom of Sensor
- Page 4 – TROUBLESHOOTING GUIDE; If you experience a problem, follow this guide.; No Service Parts Available for this Product
- Page 5 – Caractéristiques; FONCTIONNEMENT; Résumé du mode de commutation; Exigences
- Page 6 – Montage mural
- Page 7 – Bas du détecteur
- Page 8 – GUIDE DE DÉPANNAGE; Si vous éprouvez des difficultés, suivre ce guide.; Aucune pièce de rechange n’est disponible pour ce
© 2008 HeathCo LLC
598-1198-01
Models 52-4042-2 / 52-4041-4
Features
• Turns on lighting when motion is detected.
• On-Time control allows length of time light stays on
to be adjusted.
• Photocell keeps light off during daylight hours.
• LED flashes day or night to indicate motion has been
detected.
Security Light with
Motion-Activated
Sensor
OPERATION
* resets to Auto Mode at dawn.
MANUAL MODE
ON-TIME
10 5 1 TEST
10 5 1
TEST
ON-TIME
TEST
... back on.
AUTO
1 Second OFF
then...
Put the ON-TIME switch in the
1, 5, or 10 minute position.
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
•
S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Light Control
Sensor
Cover
Plate
Lamp
Holders
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Plastic Hanger
Rubber Plug
Gasket
Mounting Strap
Mounting Bolt
2 Wire
Connectors
This package includes:
6 Screws
(3 sizes included)
Mode:
On-Time
Works: Day Night
Test
5 Seconds
x
x
Auto
1, 5, or 10 Minutes
x
Manual
To Dawn*
x
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1198-01 INSTALLATION For easy installation, select an existing light with a wall switch for replacement. W ire the L ight C ontroL ❒ Route the light control’s wires through the large gasket holes. ❒ Twist the junction box wires and fixture wires together as shown. Secure with wire connectors. ...
3 598-1198-01 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 1 / 2 minute warm up period before it will detect motion. When first turned on, wait 1 1 / 2 minutes. ❒ Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. Moti...
4 598-1198-01 SYMPTOM Lights will not come on. L i g h t s c o m e o n in daylight. L i g h t s c o m e o n f o r n o a p p a r e n t reason. POSSIBLE CAUSE 1. Light switch is turned off. 2. Floodlight is loose or burned out. 3. Fuse is blown or circuit breaker is turned off. 4. Daylight turn-off is...
