Page 2 - Product description; Intended use; Product overview
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly...................................................................... 10Operation....................................
Page 3 - Symbols on the product
21. Battery22. Battery release buttons23. Warning LED24. Battery indicator button25. LED indicator for the state of charge Symbols on the product WARNING: This product can be dangerous and cause serious injury or death to the operator or others. Be careful and use the product correctly. Read the ope...
Page 4 - Manufacturer; Safety; Safety definitions; Work area safety
Manufacturer Husqvarna AB Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500 Safety Safety definitions Warnings, cautions and notes are used to point out specially important parts of the manual. WARNING: Used if there is a risk of injury or death for the operator or bystanders if the ...
Page 7 - Personal protective equipment
you are able to call for help in the event of an accident. • Always inspect the working area. Remove all loose objects such as stones, broken glass, nails, steel wire, string, etcetera, that could be thrown out or become wrapped around the cutting attachment. • Make sure that you can move and stand ...
Page 8 - Safety devices on the product
Approved protective goggles must comply with the ANSI Z87.1 standard in the USAs or EN 166 in EU countries. • Use a visor for face protection. A visor is not enough for protection of the eyes. + • Use gloves when necessary, for example when you attach, examine or clean the cutting equipment. • Use s...
Page 9 - Battery safety
2. Push the power trigger lockout forward (A) and down. Hold the power trigger lockout against the handle (B) and make sure that it returns to its original position when you release it. B A 3. Make sure that the power trigger and the power trigger lockout moves freely and that the return springs ope...
Page 10 - Assembly; Introduction
Battery charger safety WARNING: Read the warning instructions that follow before you use the product. • Risk of electrical shock or short circuit if the safety instructions are not obeyed. • Do not use other battery chargers than the one supplied for your product. Only use Husqvarna chargers when yo...
Page 11 - Operation
CAUTION: Make sure that the drive shaft (C) engages with the gear in the cutting unit. 3. Tighten the screw (A) with your fingers. Make sure that screw (A) goes into the hole in the shaft. 4. Tighten the screw (A) fully.5. Tighten the screw (B) fully. Operation Introduction WARNING: Read and underst...
Page 13 - Bluetooth
4. Hold the product near your body for a stable work position. 5. Make sure that the tip of the cutting equipment does not touch the ground. 6. Be careful and work slowly until all the branches are correctly cut. To stop the product 1. Release the power trigger or the power trigger lockout. 2. Put t...
Page 14 - Maintenance
Maintenance Introduction WARNING: Before you do any maintenance work you must read and understand the safety chapter. Maintenance schedule WARNING: Remove the battery before you do maintenance. Maintenance Before use Weekly Monthly Clean the external parts of the product. X Examine that the start an...
Page 15 - Troubleshooting; Blade
To lubricate the gear housing WARNING: Do not touch the gear housing immediately after operation of the product. The gear housing is hot and can cause injury. • Use Husqvarna special grease. Speak to your servicing dealer for more information about recommended grease. • Add the grease through the gr...
Page 16 - Transportation, storage and disposal; Transportation and storage
Problem Possible faults Possible action Error LED flashes red Overload. The cutting attachment is jammed. Stop the product. Remove the battery. Clean the cut- ting attachment from unwanted materials. Temperature deviation. Let the product cool down. The power trigger and the acti- vate button are pr...
Page 18 - Technical data
Technical data Technical data 525iHF3 Motor Motor type Husqvarna E-torq BLDC Speed of output shaft, 1/min 5800 Weight Weight without battery, kg/lb 5.7/12.6 Weight including battery BLi200, kg/lb 7.1/15.7 Blades Type Double sided Cutting length, inch/mm 25.5/650 Cutting speed, cuts/min 4200 Noise em...
Page 19 - Registered trademarks
525iHF3 Output power 4 , max dBm 0 Approved batteries Battery BLi200 40-B220X Type Lithium-ion Lithium-ion Battery capacity, Ah 5.2 6.0 Nominal voltage, V 36 36 Weight, kg (lb) 1.3 (2.9) 1.4 (3.1) Approved battery chargers Battery charger QC330 Input voltage, V 100-240 Frequency, Hz 50-60 Power, W 3...
Page 20 - Declaration of Conformity; EU Declaration of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated extended reach Hedge Trimmer Brand Husqvarna Type / Model 525iHF3 Identification Serial numbers ...