Grizzly Industrial H3140 - Manuals

-4- Model H3140 (Mfd. Since 6/02) The information contained herein is deemed accurate as of 12/22/2020 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model H3140 MACHI...

-6- Model H3140 (Mfd. Since 6/02) ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always dis...

-8- Model H3140 (Mfd. Since 6/02) Additional Safety for Belt Sanders Serious injury or death can occur from fingers, clothing, jewelry, or hair getting pinched / entangled in belt or other moving components. Abrasion injuries can occur from touching moving sandpaper with bare skin. Workpieces thrown...

Model H3140 (Mfd. Since 6/02) -9- SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize th...

Model H3140 (Mfd. Since 6/02) -11- SECTION 3: SETUP Description Qty• Safety Glasses ................. 1 Pair Per Person • 2" Dust Hose and Clamp ......................1 Ea. • Dust Collection System .............................. 1 Needed for Setup This machine presents serious injury hazards to ...

-12- Model H3140 (Mfd. Since 6/02) Box 1: (Figure 3) Qty A. Machine ...................................................... 1 B. Work Table ................................................. 3 C. Table Lock Lever Assembly ....................... 1 — Lever .................................................

Model H3140 (Mfd. Since 6/02) -13- Assembly To assemble your machine: 1. Slide the table over the sanding belt, then attach it to the machine base with the M8-1.25 x 25 hex bolt, 8mm external tooth washer, and the table lock lever, as shown in ( Figure 5). Figure 5. Attaching work table. 2. Adjust t...

-14- Model H3140 (Mfd. Since 6/02) Test Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix...

Model H3140 (Mfd. Since 6/02) -15- SECTION 4: OPERATIONS Loose hair, clothing, or jewelry could get caught in machinery and cause serious personal injury. Keep these items away from moving parts at all times to reduce this risk. Basic Controls Use Figure 7 and the descriptions below to become famili...

-16- Model H3140 (Mfd. Since 6/02) Operation Overview Stock Inspection To avoid the risk of kickback and personal injury, always keep the workpiece firmly on the table. A basic operation with this machine is as follows: The operator adjusts the table as needed for the sanding operation, then turns t...

Model H3140 (Mfd. Since 6/02) -17- Table Tilt The table on the Model H3140 can tilt to allow for sanding of miter cut and other angled workpieces. To tilt the table: 1. DISCONNECT SANDER FROM POWER! 2. Loosen the table lock lever to release the table position ( Figure 9). The table on the Model H314...

-20- Model H3140 (Mfd. Since 6/02) SECTION 5: ACCESSORIES ACCESSORIES PRO-STICK ® Abrasive Surface Cleaners Extend the life of your sanding discs and belts! Choose the Pro-Stick ® with a handle for greater control or without a handle for more usable area. Size Model 1 1 ⁄ 2 " X 1 1 ⁄ 2 " X 8...

-22- Model H3140 (Mfd. Since 6/02) SECTION 6: MAINTENANCE Cleaning the Model H3140 is relatively easy. Vacuum excess sawdust, and wipe off the remain-ing dust with a dry cloth. Wiping the table clean after every use ensures moisture from wood dust does not remain on bare metal surfaces. If any resin...

Model H3140 (Mfd. Since 6/02) -23- SECTION 7: SERVICE Troubleshooting Symptom Possible Cause Possible Solution Motor will not start; fuses/circuit breakers trip. 1. Breaker or fuse at fault.2. Loose connection or short in line cord, plug, or motor. 3. Machine attached to incorrect power circuit. 1. ...

-24- Model H3140 (Mfd. Since 6/02) SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before s...

Model H3140 (Mfd. Since 6/02) -25- READ ELECTRICAL SAFETY ON PAGE 24! POWER SWITCH (viewed from behind) TO MOTOR Neutral Hot Ground Ground 110 VAC 5-15 Plug Start Capacitor 12MFD 250VAC The motor wiring shown here is current at the time of printing, but it may not match your machine. Always use the ...

Model H3140 (Mfd. Since 6/02) -27- BUY PARTS ONLINE AT GRIZZLY.COM ! Scan QR code to visit our Parts Store. Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH3140001 SUPPORTING FOOT 27 PH3140027 COMPRESSION SPRING 6MM 2 PH3140002 HEX BOLT M8-1.25 X 16 28 PH3140028 SHOULDER SCREW M4-....

-4- Model h3140 (Mfg. after 6/02) The information contained herein is deemed accurate as of 3/3/2009 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model H3140 MACHINE...

-6- Model h3140 (Mfg. after 6/02) Safety instructions for Machinery 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing loss. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry that can catch in moving parts. Wea...

-8- Model h3140 (Mfg. after 6/02) Additional Safety for Belt Sanders 5. iNSpEcTiNg WORKpiEcES. always inspect workpiece for nails, staples, knots, and other imperfections that could be dis-lodged and thrown from the machine during sanding operations. do not use workpieces that show any of these cond...

Model h3140 (Mfg. after 6/02) -9- figure 2. typical 5-15 plug and receptacle. Grounding Prong is Longest of the Three Prongs Current Carrying Prongs Grounded Outlet 110v Operation full Load Amperage Draw this machine draws the following amps under maximum load: amp draw ................................

-10- Model h3140 (Mfg. after 6/02) Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! SEcTiON 3: SETup Descripti...

Model h3140 (Mfg. after 6/02) -11- inventory the following is a description of the main compo-nents shipped with your machine. lay the compo-nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefu...

-12- Model h3140 (Mfg. after 6/02) Assembly To assemble your machine: 1. slide the table over the sanding belt, then attach it to the machine base with the M8-1.25 x 25 hex bolt, 8mm external tooth washer, and the table lock lever, as shown in ( figure 5). figure 5. Attaching work table. 2. adjust t...

Model h3140 (Mfg. after 6/02) -13- Test Run once the assembly is complete, test run your machine to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on page 2...

-14- Model h3140 (Mfg. after 6/02) SEcTiON 4: OpERATiONS Damage to your eyes and lungs could result from using this machine without proper pro- tective gear. Always wear safety glasses and a respirator when operating this machine. notice if you have never used this type of machine or equipment befor...

Model h3140 (Mfg. after 6/02) -15- Operation Overview Stock inspection To avoid the risk of kickback and personal injury, always keep the workpiece firmly on the table. a basic operation with this machine is as follows: the operator adjusts the table as needed for the sanding operation, then turns t...

-16- Model h3140 (Mfg. after 6/02) Table Tilt the table on the Model h3140 can tilt to allow for sanding of miter cut and other angled workpieces. To tilt the table: 1. disConneCt sander FroM poWer! 2. loosen the table lock lever to release the table position ( figure 9). the table on the Model h314...

Model h3140 (Mfg. after 6/02) -19- SEcTiON 5: AccESSORiES aCCessories pRO-STicK ® Abrasive Surface cleaners extend the life of your sanding discs and belts! Choose the pro-stick ® with a handle for greater control or without a handle for more usable area. Size Model 1 1 ⁄ 2 " X 1 1 ⁄ 2 " X 8...

Model h3140 (Mfg. after 6/02) -21- SEcTiON 6: MAiNTENANcE Always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructio...

-22- Model h3140 (Mfg. after 6/02) review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663. SEcTiON 7: SERvicE...

Model h3140 (Mfg. after 6/02) -23- POWER SWITCH (viewed from behind) TO MOTOR Neutral Hot Ground Ground 110 VAC 5-15 Plug Start Capacitor 12MFD 250VAC View this page in color at www.grizzly.com. The motor wiring shown here is current at the time of printing, but it may not match your machine. Always...

-24- Model h3140 (Mfg. after 6/02) 1 2 3 4 5 7 8 9 10 11 12 12 13 13 14 14 15 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 31-1 52 31-2 31-3 31-4 53 54 55 parts Breakdown SEcTiON 8: pARTS

Model h3140 (Mfg. after 6/02) -25- parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH3140001 SUPPORTING FOOT 27 PH3140027 COMPRESSION SPRING 6MM 2 PB03M HEX BOLT M8-1.25 X 16 28 PH3140028 SHOULDER SCREW M4-.7 X 14 3 PLW04M LOCK WASHER 8MM 29 PH3140029 TABLE 4 PH3140004 BASE 30 PSS11M SET ...

-26- Model h3140 (Mfg. after 6/02) 101 102 103 104 105 Labels Breakdown & List Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MuST maintain the original location and readability of the labels on the machine. if any label is removed or becomes unrea...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

WARRANTy AND RETuRNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website Today And Discover Why Grizzly ® Is The Industry Leader! Call Today For A FREE Full Color Catalog