Grizzly Industrial G0897 - User Manual

-4- Model G0897 (Mfd. Since 6/19) Controls & Components To reduce your risk of serious injury, read this entire manual BEFORE using machine. Component Descriptions Refer to the following figures and descriptions to become familiar with the basic controls and com-ponents of this machine. Understa...

Model G0897 (Mfd. Since 6/19) -5- Machine Data Sheet The information contained herein is deemed accurate as of 7/10/2019 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2...

Model G0897 (Mfd. Since 6/19) -7- ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always dis...

Model G0897 (Mfd. Since 6/19) -9- Additional Safety for Metalworking Grinders Serious injury or death can occur from fingers, clothing, jewelry, or hair getting pinched / entangled in rotating belt or other moving components. Abrasion injuries can occur from touching moving grinding belt with bare s...

-10- Model G0897 (Mfd. Since 6/19) SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize t...

Model G0897 (Mfd. Since 6/19) -13- NOTICE If you cannot find an item on this list, care- fully check around /inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory. The following is a list of items shi...

-14- Model G0897 (Mfd. Since 6/19) Hardware Recognition Chart USE THIS CHART TO MATCH UPHARDWARE DURING THE INVENTORYAND ASSEMBLY PROCESS. 5mm 5 mm Flat Head Cap Screw

Model G0897 (Mfd. Since 6/19) -15- Site Considerations Workbench/Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some workbenches may require additional rein-forcement to support the weight of the machine and workpiece materials. Consider antic...

Model G0897 (Mfd. Since 6/19) -17- Anchoring to Floor Lag shield anchors with lag screws (see below) are a popular way to anchor machinery to a con-crete floor, because the anchors sit flush with the floor surface, making it easy to unbolt and move the machine later, if needed. However, anytime loca...

-18- Model G0897 (Mfd. Since 6/19) 5. Push Emergency Stop button up to open switch cover (be sure to leave switch cover open; closing it will prevent operation). 6. Use ON/OFF buttons to start and imme- diately stop grinder, while watching how belt tracks on contact wheel. Belt "tracking" re...

Model G0897 (Mfd. Since 6/19) -19- SECTION 4: OPERATIONS To reduce your risk of serious injury, read this entire manual BEFORE using machine. If you are not experienced with this type of machine, WE STRONGLY RECOMMEND that you seek additional training outside of this manual. Read books /magazines or...

-22- Model G0897 (Mfd. Since 6/19) Flat grinding operations can be performed directly on the belt against the platen. Always use two hands to control the workpiece and use the work stop to support it. To perform flat grinding: 1. Connect machine to power, turn it ON, and allow it to reach full speed...

Model G0897 (Mfd. Since 6/19) -23- ACCESSORIES order online at www.grizzly.com or call 1-800-523-4777 SECTION 5: ACCESSORIES PRO-STIK ® Abrasive Surface Cleaners Extend the life of your abrasive discs and sleeves! Choose the Pro-Stik ® with a handle for greater control or without a handle for more u...

Model G0897 (Mfd. Since 6/19) -25- SECTION 6: MAINTENANCE Cleaning the Model G0897 is relatively easy. Vacuum excess shavings, and wipe off any remaining dust with a dry cloth. Never use com-pressed air to blow away dust as airborne par-ticles may be combustible. Cleaning & Protecting To empty t...

-26- Model G0897 (Mfd. Since 6/19) Review the troubleshooting procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please gather the serial number and manufacture date of your machine ...

Model G0897 (Mfd. Since 6/19) -27- Operation Symptom Possible Cause Possible Solution Machine vibrates excessively (non-motor related). 1. Stand not stable on floor.2. Broken/defective grinding belt. 1. Relocate/shim machine.2. Replace grinding belt ( Page 20). Grains easily rub off belt. 1. Belt ha...

-28- Model G0897 (Mfd. Since 6/19) SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before s...

Model G0897 (Mfd. Since 6/19) -29- READ ELECTRICAL SAFETY ON PAGE 28! Wiring Diagram Figure 30. Motor junction box. Figure 31. ON/OFF switch. MOTOR JUNCTION BOX ON/OFF SWITCH (viewed from behind) Run Capacitor 60MFD 300VAC 3 4 7 8 Rd Grd Gn Rd Bk Rd Bl Bk Bk Neutral Hot Ground 110 VAC 5-15 Plug Grd ...

Model G0897 (Mfd. Since 6/19) -31- BUY PARTS ONLINE AT GRIZZLY.COM ! Scan QR code to visit our Parts Store. Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0897001 HEX BOLT M8-1.25 X 16 44 P0897044 WHEEL SHIELD 2 P0897002 FLAT WASHER 8MM 45 P0897045 FLAT WASHER 6MM 3 P0897003 STAND ...