Grizzly Industrial G0489 - Manuals

-4- G0489 Metalworking Sander Figure 1. Machine Identification. A. Spark Trap B. Eye Shield C. Tool/Work Rests D. Belt Tracking Adjustment Knob E. Belt Tension Release Lever F. ON/OFF Switch Identification A I G F E D C B C J K L H G. Angle Adjustment Lever H. Dust Port I. Belt Guards Long & Sho...

G0489 Metalworking Sander -5- ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always disconn...

G0489 Metalworking Sander -7- Additional Safety for Belt Sanders 8. FEEDING STOCK. Firmly grasp the workpiece in both hands and ease it into the machine using light pressure. DO NOT jam the workpiece into the machine during operation. Feed the workpiece against the direction of rotation. DO NOT sand...

-8- G0489 Metalworking Sander Serious personal injury could occur if you connect your machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. 220 3-Phase SECTION 2: CIRCUIT REQUIREMENTS Amperage Draw The Mo...

-10- G0489 Metalworking Sander Wear safety glasses dur- ing the entire set up pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Set Up Safety SECTION 3: SET ...

G0489 Metalworking Sander -11- Inventory After all the parts have been removed from the two boxes, you should have the following items: Box 1: (Figures 4, & 5) Qty A. Metalworking Sander .................................. 1 B. Spark Trap .................................................. 1 C. Re...

-12- G0489 Metalworking Sander Figure 6. Minimum working clearances. Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some floors may require additional reinforcement to support both the machine and operator. Working Clearances Consider existing...

G0489 Metalworking Sander -13- Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included. Generally, you can either bolt your machine to the floor or mount it on machine mou...

-16- G0489 Metalworking Sander Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and cloth- ing could get caught in machinery and cause ser...

G0489 Metalworking Sander -17- Grinding Tips • When grinding against the contact wheel, make sure the belt guard is closed. • Hold work piece securely with both hands. Use the rests when possible to support the workpiece. • The workpiece will get hot as you continue to grind. Cool the workpiece freq...

-18- G0489 Metalworking Sander Figure 18. Belt replacement. Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Changing the belt on the Model G0489 is quick and easy. To change the belt: 1. DISCONNECT THE SANDER FROM THE ...

G0489 Metalworking Sander -19- BLACK ............... BLUE .................... GREEN ............... RED .................... BROWN ............... B B B B B G G G G Bl Bl Bl Bl Bl R R Br Br Br Br Br COLOR KEY G 15-15P G W Z X Electrical Components & Wiring Diagram Motor Switch

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

-4- G0489 Metalworking Sander Figure 1. Machine Identification. A. Spark Trap B. Eye Shield C. Tool/Work Rests D. Belt Tracking Adjustment Knob E. Belt Tension Release Lever F. ON/OFF Switch Identification A I G F E D C B C J K L H G. Angle Adjustment Lever H. Dust Port I. Belt Guards Long & Sho...

G0489 Metalworking Sander -5- 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to ...

G0489 Metalworking Sander -7- Additional Safety for Belt Sanders 8. FEEDING STOCK. Firmly grasp the workpiece in both hands and ease it into the machine using light pressure. DO NOT jam the workpiece into the machine during operation. Feed the workpiece against the direction of rotation. DO NOT sand...

-8- G0489 Metalworking Sander Serious personal injury could occur if you connect your machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. 220 3-Phase SECTION 2: CIRCUIT REQUIREMENTS Amperage Draw The Mo...

-10- G0489 Metalworking Sander The Model G0489 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materials for possible...

G0489 Metalworking Sander -11- Inventory After all the parts have been removed from the two boxes, you should have the following items: Box 1: (Figures 4 & 5) Qty A. Metalworking Sander .................................. 1 B. Spark Trap .................................................. 1 C. Eye...

-12- G0489 Metalworking Sander Figure 6. Minimum working clearances. Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some floors may require additional reinforcement to support both the machine and operator. Working Clearances Consider existing...

G0489 Metalworking Sander -13- Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included. Generally, you can either bolt your machine to the floor or mount it on machine mou...

-14- G0489 Metalworking Sander Mounting Sander This step may require three people to complete—two to lift and hold the sander in place, and one person to install the hardware. Components and Hardware Needed: Qty Sleeve ................................................................ 1Hex Bolt M12-1....

-16- G0489 Metalworking Sander Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and cloth- ing could get caught in machinery and cause ser...

-18- G0489 Metalworking Sander Figure 18. Belt replacement. Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Changing the belt on the Model G0489 is quick and easy. To change the belt: 1. DISCONNECT THE SANDER FROM THE ...

G0489 Metalworking Sander -19- ����� ��������������� ���� �������������������� ����� ��������������� ��� �������������������� ����� ��������������� � � � � � � � � � �� �� �� �� �� � � �� �� �� �� �� ��������� � ������ � � � � Electrical Components & Wiring Diagram Motor Switch

-22- G0489 Metalworking Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or la...