Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .....................................................................................................................................
Page 4 - Foreword; INTRODUCTION; Contact Info
-2- G0538 Oscillating Spindle Sander If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C ⁄ O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or part...
Page 5 - MACHINE DATA; Machine Data Sheet
G0538 Oscillating Spindle Sander -3- The information contained herein is deemed accurate as of 11/29/2005 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0538 MA...
Page 7 - Identification
G0538 Oscillating Spindle Sander -5- Figure 1. Identification. A. Spindle B. Table C. Sanding Sleeve D. Spindle Washer E. Throat Plate F. Sander Body G. Accessory Storage Area H. ON⁄OFF Paddle Switch with Lockout Key I. 5-15 Plug and Power Cable J. 2 1 ⁄ 2 " Dust Port (not shown) Identification ...
Page 8 - NOTICE; Safety Instructions for Machinery
-6- G0538 Oscillating Spindle Sander 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair cover...
Page 10 - Safety Instructions for Spindle Sanders
-8- G0538 Oscillating Spindle Sander 1. FEED RATE. Never jam a workpiece against the sanding surface. Firmly hold the workpiece and ease it against the spindle using light pressure. 2. AVOIDING ENTANGLEMENT. Keep loose clothing articles such as sleeves, belts or jewelry items away from the spindle. ...
Page 11 - SECTION 2: CIRCUIT REQUIREMENTS
G0538 Oscillating Spindle Sander -9- Figure 2. Typical type 5-15 plug and receptacle. Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. 110V Oper...
Page 12 - Unpacking; Items Needed for
-10- G0538 Oscillating Spindle Sander The Model G0538 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing materials for p...
Page 13 - Inventory
G0538 Oscillating Spindle Sander -11- Figure 4. Pre-Installed Components. Figure 3. Inventory. Inventory After all the parts have been removed from the box, you should have the following items: Inventory (Figure 3) Qty A. Sander Unit ................................................ 1 B. Sander Unit ...
Page 14 - Base Attachment; Mounting
-12- G0538 Oscillating Spindle Sander Base Attachment The metal base plate needs to be attached to the spindle sander before use. Components and Hardware Needed: Qty Tap Screw M4-0.7 x 12 ..................................... 4Sander Base Plate ............................................ 1 To attac...
Page 15 - SECTION 4: OPERATIONS; Switch ⁄ Safety Key; Sleeve Installation
G0538 Oscillating Spindle Sander -13- Using this machine pro- duces dust which may cause allergic reactions and respiratory prob- lems. Protect yourself by wearing safety glasses and a respirator dur- ing the entire operation process. DO NOT wear gloves while operating this machine as they can be ca...
Page 16 - Sanding
-14- G0538 Oscillating Spindle Sander Figure 8. Loosening the spindle hex nut. 3. Remove the hex nut, upper spindle washer, sanding sleeve, sanding drum, and throat plate. 4. Clean the throat plate and lower spindle washer areas as necessary. 5. Replace the lower spindle washer. 6. Install the throa...
Page 17 - SECTION 5: ACCESSORIES
G0538 Oscillating Spindle Sander -15- H5430-H5459 Sanding Sleeves Grizzly stocks a wide variety of aluminum oxide sanding sleeves of varying sizes and grits. All our 4½" long sanding sleeves are available in 60 to 150 grit and from ½ " to 3" in diameter, and come in packs of three. MODEL...
Page 18 - Cleaning; SECTION 6: MAINTENANCE; Schedule
-16- G0538 Oscillating Spindle Sander Cleaning the Model G0538 is relatively easy. Follow the Sleeve Installation instructions on Page 15 , taking special care to clean every area thoroughly. However, sawdust and other particles can also work their way under the rotation mark plate. To clean under t...
Page 19 - Troubleshooting
G0538 Oscillating Spindle Sander -17- Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. SECTION 7: SERVICE Trouble...
Page 21 - Wiring Diagram
G0538 Oscillating Spindle Sander -19- �������� ����� ����������������������� ������������ ����� ����� ��� ����� ����� ������ ��������� Wiring Diagram Disconnect power from machine before perform- ing any electrical ser- vice. Failure to do this will result in a shock haz- ard, leading to injury or d...
Page 22 - Parts Breakdown
-20- G0538 Oscillating Spindle Sander � � � ��� � � � � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��� �� �� �� �� �� �� �� �� ��� ��� ��� ��� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� Parts ...
Page 23 - Parts List
G0538 Oscillating Spindle Sander -21- REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PN03M HEX NUT M8-1.25 37 P0538037 BRACING WHEEL AXLE 2 P0538002 SPINDLE WASHER 8 X 24 X 2 38 PHTEK20M TAP SCREW M5 X 14 3 P0538003 SANDING SLEEVE 1" X 4-1/2" 39 P0538039 BRACING WHEEL BASE 4-1 P0538004-1 SA...
Page 24 - WARRANTY AND RETURNS
-22- G0538 Oscillating Spindle Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alteration...
