Page 2 - WARNING; • Arsenic and chromium from chemically treated
-B- G9984/G9985 Oscillating Belt Edge Sander WARNING Some dust created by power sanding, sawing, grind-ing, drilling, and other construction activities containschemicals known to the State of California to causecancer, birth defects or other reproductive harm. Someexamples of these chemicals are: • ...
Page 3 - Table Of Contents
G9984/G9985 Oscillating Belt Edge Sander -1- Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR POWER TOOLS ..............................................................2-3ADDITIONAL SAFETY INSTRUCTIONS FOR EDGE SANDERS ..........................4 2. CIRCUIT REQUIREMENTS 220V SINGLE-PHASE OPERATION ...
Page 5 - Safety Instructions For Power Tools
G9984/G9985 Oscillating Belt Edge Sander -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi-tion. Conductor size should be in accor-dance with the chart below. The amperagerating should be listed on the motor or toolnameplate. An undersized cord will causea drop in lin...
Page 7 - SECTION 2: CIRCUIT REQUIREMENTS
G9984/G9985 Oscillating Belt Edge Sander -5- SECTION 2: CIRCUIT REQUIREMENTS 220V Single-Phase 220V Three-Phase G9984 Only: The Model G9984 has a 3 H.P., 1725 R.P.M.motor which requires a 220V single-phase circuit.The cord set included does not have a plug, asthe style of plug you require will depen...
Page 8 - Grounding
-6- G9984/G9985 Oscillating Belt Edge Sander We do not recommend the use of extension cordswith 220V equipment. It is much better to arrangethe placement of your equipment and the installedwiring to eliminate the need for extension cords.Should it be necessary to use an extension, makesure the cord ...
Page 9 - SECTION 3: INTRODUCTION; Commentary
G9984/G9985 Oscillating Belt Edge Sander -7- SECTION 3: INTRODUCTION We are proud to offer the Grizzly ModelG9984/G9985 Oscillating Belt Edge Sander . TheModel G9984/G9985 is part of a growing Grizzlyfamily of fine woodworking machinery. Whenused according to the guidelines set forth in thismanual, ...
Page 10 - Unpacking
-8- G9984/G9985 Oscillating Belt Edge Sander Unpacking The Model G9984/G9985 is shipped from themanufacturer in a carefully packed carton. If youdiscover the machine is damaged after you havesigned for delivery, immediately call CustomerService for advice. The Model G9984/G9985 has two lifting rings...
Page 11 - Piece Inventory
G9984/G9985 Oscillating Belt Edge Sander -9- Piece Inventory After all the parts have been removed from the carton, you should have: • (2) Base Support• (2) Star Knob M10-1.5 x 15• (4) Lock Washer 10mm• (6) Flat Washer 10mm• (4) Hex Bolt M10-1.5 x 30• (4) Rubber Foot 1 ⁄ 2 "-12 x 1 • (1) Sanding...
Page 12 - Hardware Recognition Chart
-10- G9984/G9985 Oscillating Belt Edge Sander Hardware Recognition Chart 5mm 10mm15mm20mm25mm30mm35mm40mm45mm50mm55mm60mm65mm70mm75mm Washer Lock Washer Hex Nut Wing Nut Phillips HeadSheetMetalScrew Setscrew Phillips Head Screw ThumbScrew Slotted Screw CountersunkPhillipsHead Screw Cap Screw Carriag...
Page 13 - Clean Up; Site Considerations
G9984/G9985 Oscillating Belt Edge Sander -11- Clean Up The unpainted surfaces are coated with a waxy oilto protect them from corrosion during shipment.Remove this protective coating with a solventcleaner or citrus-based degreaser such asGrizzly’s G7895 Degreaser. Avoid chlorine-basedsolvents as they...
Page 14 - Rubber Feet; Beginning Assembly
-12- G9984/G9985 Oscillating Belt Edge Sander SECTION 4: ASSEMBLY Most of your Model G9984/G9985 has beenassembled at the factory, but some parts must beassembled or installed after delivery. TOOLS REQUIRED: You will need a small adjustable wrench, a flat and Phillips head screw-driver, and a machin...
Page 15 - Base Supports
G9984/G9985 Oscillating Belt Edge Sander -13- Attaching the base supports to the main base: 1. Slide the base supports under the mainmachine base. 2. Using (4) M10-1.5 x 30 hex bolts, (4) 10mmflat washers, and (4) 10mm lock washers,secure the main machine base to the basesupports as shown in Figure ...
Page 16 - SECTION 5: ADJUSTMENTS; Power Switch; Dust Collection
-14- G9984/G9985 Oscillating Belt Edge Sander SECTION 5: ADJUSTMENTS Disconnect power to themachine when perform-ing any adjustments onthe Model G9984/G9985.Failure to do this mayresult in serious person-al injury. Wear safety glassesduring the entire adjust-ment process. Failure tocomply may result...
Page 18 - Sanding Belt
-16- G9984/G9985 Oscillating Belt Edge Sander The main table is adjustable to accommodate awide range of workpieces and sanding operations.Because the main table is designed with a specialbalance mount, it is easily adjusted up and down.To adjust the main table: 1. Loosen the lock handles on the fro...
Page 19 - Miter Gauge; Main Table Angle
G9984/G9985 Oscillating Belt Edge Sander -17- The main table has a stationary miter gauge thatis used to hold the workpiece at various anglesagainst the sanding belt. To adjust the mitergauge: 1. Loosen the lock handle shown in Figure 16 . 2. Rotate the miter gauge to the desired angle. 3. While hol...
Page 21 - SECTION 6: OPERATIONS; Test Run
G9984/G9985 Oscillating Belt Edge Sander -19- SECTION 6: OPERATIONS Once assembly is complete and adjustments aredone to your satisfaction, you are ready to test runthe machine. Turn on the power supply at the main panel.Press the START button. Make sure that your fin-ger is poised on the switch, ju...
Page 22 - SECTION 7: MAINTENANCE; Lubrication; General
-20- G9984/G9985 Oscillating Belt Edge Sander SECTION 7: MAINTENANCE Lubrication There are (2) grease fittings shown in Figure 20 . Grease these points after approximately 50 hoursof use. All other bearings are sealed and permanentlylubricated, simply leave them alone until theyneed to be replaced. ...
Page 26 - GRIZZLY MODEL G9984 OSCILLATING EDGE SANDER
-24- G9984/G9985 Oscillating Belt Edge Sander Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type ...................................................................................................... Floor Model Overall Dimension...
Page 27 - GRIZZLY MODEL G9985 OSCILLATING EDGE SANDER; MACHINE DATA
G9984/G9985 Oscillating Belt Edge Sander -25- Design Type ...................................................................................................... Floor Model Overall Dimensions and Specifications: Table Size.................................................................................
Page 38 - NOTES
-36- G9984/G9985 Oscillating Belt Edge Sander NOTES
Page 40 - WARRANTY AND RETURNS
-38- G9984/G9985 Oscillating Belt Edge Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alt...
Page 41 - WARRANTY CARD
10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt S...
