Page 3 - Table of Contents
INTRODUCTION ............................................................................................................................... 2 Manual Accuracy ........................................................................................................................ 2Contact Info .........
Page 4 - INTRODUCTION; Machine Description; Contact Info; Manual Accuracy
-2- Model H3140 (Mfd. Since 6/02) INTRODUCTION The Model H3140 1" x 30" Belt Sander provides a moving abrasive surface that can be used to shape and contour small workpieces. By tilting the adjustable table, sanding operations can be per-formed on miter-cut, or other angled workpieces. The b...
Page 5 - Identification
Model H3140 (Mfd. Since 6/02) -3- Figure 1. Identification. Identification Foot Table Motor ON/OFF Switch Belt Cover Knob Table Stop Adjustment Bolt Sanding Belt 2" Dust Port Platen Table Tilt Lock Lever Contour Sanding Shield Sanding Belt Side Cover Sanding Belt Tracking/Tension Release Knob To...
Page 6 - Machine Data Sheet
-4- Model H3140 (Mfd. Since 6/02) The information contained herein is deemed accurate as of 12/22/2020 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model H3140 MACHI...
Page 8 - NOTICE; Safety Instructions for Machinery
-6- Model H3140 (Mfd. Since 6/02) ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and always dis...
Page 10 - Additional Safety for Belt Sanders
-8- Model H3140 (Mfd. Since 6/02) Additional Safety for Belt Sanders Serious injury or death can occur from fingers, clothing, jewelry, or hair getting pinched / entangled in belt or other moving components. Abrasion injuries can occur from touching moving sandpaper with bare skin. Workpieces thrown...
Page 11 - SECTION 2: POWER SUPPLY; Availability
Model H3140 (Mfd. Since 6/02) -9- SECTION 2: POWER SUPPLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize th...
Page 13 - Needed for Setup; Unpacking
Model H3140 (Mfd. Since 6/02) -11- SECTION 3: SETUP Description Qty• Safety Glasses ................. 1 Pair Per Person • 2" Dust Hose and Clamp ......................1 Ea. • Dust Collection System .............................. 1 Needed for Setup This machine presents serious injury hazards to ...
Page 14 - Placement Location; Site Considerations; Inventory
-12- Model H3140 (Mfd. Since 6/02) Box 1: (Figure 3) Qty A. Machine ...................................................... 1 B. Work Table ................................................. 3 C. Table Lock Lever Assembly ....................... 1 — Lever .................................................
Page 15 - Assembly; Dust Collection
Model H3140 (Mfd. Since 6/02) -13- Assembly To assemble your machine: 1. Slide the table over the sanding belt, then attach it to the machine base with the M8-1.25 x 25 hex bolt, 8mm external tooth washer, and the table lock lever, as shown in ( Figure 5). Figure 5. Attaching work table. 2. Adjust t...
Page 16 - Test Run
-14- Model H3140 (Mfd. Since 6/02) Test Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning correctly. If you find an unusual problem during the test run, immediately stop the machine, disconnect it from power, and fix...
Page 17 - SECTION 4: OPERATIONS; Basic Controls
Model H3140 (Mfd. Since 6/02) -15- SECTION 4: OPERATIONS Loose hair, clothing, or jewelry could get caught in machinery and cause serious personal injury. Keep these items away from moving parts at all times to reduce this risk. Basic Controls Use Figure 7 and the descriptions below to become famili...
Page 18 - Sanding Tips
-16- Model H3140 (Mfd. Since 6/02) Operation Overview Stock Inspection To avoid the risk of kickback and personal injury, always keep the workpiece firmly on the table. A basic operation with this machine is as follows: The operator adjusts the table as needed for the sanding operation, then turns t...
Page 19 - Table Tilt; ° Stop Adjustment
Model H3140 (Mfd. Since 6/02) -17- Table Tilt The table on the Model H3140 can tilt to allow for sanding of miter cut and other angled workpieces. To tilt the table: 1. DISCONNECT SANDER FROM POWER! 2. Loosen the table lock lever to release the table position ( Figure 9). The table on the Model H314...
Page 22 - SECTION 5: ACCESSORIES
-20- Model H3140 (Mfd. Since 6/02) SECTION 5: ACCESSORIES ACCESSORIES PRO-STICK ® Abrasive Surface Cleaners Extend the life of your sanding discs and belts! Choose the Pro-Stick ® with a handle for greater control or without a handle for more usable area. Size Model 1 1 ⁄ 2 " X 1 1 ⁄ 2 " X 8...
Page 24 - SECTION 6: MAINTENANCE; Cleaning; Schedule
-22- Model H3140 (Mfd. Since 6/02) SECTION 6: MAINTENANCE Cleaning the Model H3140 is relatively easy. Vacuum excess sawdust, and wipe off the remain-ing dust with a dry cloth. Wiping the table clean after every use ensures moisture from wood dust does not remain on bare metal surfaces. If any resin...
Page 25 - Troubleshooting
Model H3140 (Mfd. Since 6/02) -23- SECTION 7: SERVICE Troubleshooting Symptom Possible Cause Possible Solution Motor will not start; fuses/circuit breakers trip. 1. Breaker or fuse at fault.2. Loose connection or short in line cord, plug, or motor. 3. Machine attached to incorrect power circuit. 1. ...
Page 26 - Wiring Safety Instructions
-24- Model H3140 (Mfd. Since 6/02) SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before s...
Page 27 - Wiring Diagram
Model H3140 (Mfd. Since 6/02) -25- READ ELECTRICAL SAFETY ON PAGE 24! POWER SWITCH (viewed from behind) TO MOTOR Neutral Hot Ground Ground 110 VAC 5-15 Plug Start Capacitor 12MFD 250VAC The motor wiring shown here is current at the time of printing, but it may not match your machine. Always use the ...
Page 29 - Main Parts List
Model H3140 (Mfd. Since 6/02) -27- BUY PARTS ONLINE AT GRIZZLY.COM ! Scan QR code to visit our Parts Store. Main Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH3140001 SUPPORTING FOOT 27 PH3140027 COMPRESSION SPRING 6MM 2 PH3140002 HEX BOLT M8-1.25 X 16 28 PH3140028 SHOULDER SCREW M4-....
