Grizzly Industrial G1183 - Manuals

-8- Model G1183/G1276 (Mfg. Since 3/10) ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or improperly grounded machinery. To reduce this risk, only allow qualified service personnel to do electrical installation or repair work, and alwa...

-10- Model G1183/G1276 (Mfg. Since 3/10) Additional Safety for Combination Sanders WORKpIECE INSpECTION. nails, staples, knots, or other imperfections in the workpiece can be dislodged and thrown from the sander at a high rate of speed into the operator or bystanders, or cause damage to sandpaper or...

Model G1183/G1276 (Mfg. Since 3/10) -11- SECTION 2: pOWER SUppLY Availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To mini...

Model G1183/G1276 (Mfg. Since 3/10) -13- Extension Cords We do not recommend using an extension cord with this machine. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis. Extension cords cause voltage drop, which may damage electrical components and...

-14- Model G1183/G1276 (Mfg. Since 3/10) Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! SECTION 3: SETUp the...

Model G1183/G1276 (Mfg. Since 3/10) -15- Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency...

-16- Model G1183/G1276 (Mfg. Since 3/10) The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean. Be patient and do a thorough job c...

Model G1183/G1276 (Mfg. Since 3/10) -17- Site Considerations figure 9. minimum working clearances. 32" 32" Dust Hose Dust Hose Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the m...

-22- Model G1183/G1276 (Mfg. Since 3/10) Dust Collection Recommended CfM at: 3" dust port ................................ 220 CFm2 1 ⁄ 2 " dust hose ........................... 150 CFm Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the ...

Model G1183/G1276 (Mfg. Since 3/10) -23- Test Run once the assembly is complete, test run your machine to make sure it runs properly. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on ...

-24- Model G1183/G1276 (Mfg. Since 3/10) SECTION 4: OpERATIONS Operation Overview The purpose of this overview is to provide the nov-ice machine operator with a basic understanding of how the machine is used during operation, so the machine controls/components discussed later in this manual are easi...

Model G1183/G1276 (Mfg. Since 3/10) -25- Table Tilt angle sanding is performed with the table tilted away from 0° (perpendicular to the sanding sur-face). Compound angles are sanded using a com-bination of table tilt and miter gauge angle. Table Tilt Rangessanding Belt table ...........................

-28- Model G1183/G1276 (Mfg. Since 3/10) Belt Sanding the sanding belt removes material faster than the sanding disc, and can be secured at any angle from horizontal to completely vertical with the use of the pivot cap screw shown in figure 36. figure 36. positioning the sanding belt assembly. pivot...

-30- Model G1183/G1276 (Mfg. Since 3/10) SECTION 5: ACCESSORIES Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Gr...

-32- Model G1183/G1276 (Mfg. Since 3/10) SECTION 6: MAINTENANCE For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Before & During Operation:• loose mounting bolts. • damaged, excessively worn, or clogged sand...

Model G1183/G1276 (Mfg. Since 3/10) -33- review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663. SECTION 7: S...

Model G1183/G1276 (Mfg. Since 3/10) -35- — if the platen is not even with or is higher than the upper roller crown, loosen the platen cap screw shown in figure 49, adjust the platen even with the middle of the top roller, then re-tighten the cap screw to secure the platen in place. 5. replace the sa...

Model G1183/G1276 (Mfg. Since 3/10) -37- these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. study this section carefully. if there are differences between your machine and what is shown in this se...

-40- Model G1183/G1276 (Mfg. Since 3/10) 1 2 3 4 5 6 7V2-1 7V2-2 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36V2 37 38 39 40 41 41-1 42 43 44 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 74 76 80 81 82 83 84 85 86 87 88 89 90...

Model G1183/G1276 (Mfg. Since 3/10) -41- REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P1183001 BASE ALUMINUM 42 PW04 FLAT WASHER 7/16 2 P1183002 BASE PLATE PLASTIC 43 P1183043 STAR KNOB 3 PB06M HEX BOLT M8-1.25 X 12 44 P1183044 POINTER 4 PFS03 FLANGE SCREW 10-24 X 3/8 45 PS18 PHLP HD SCR 10-24 X ...

C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...

WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...

G1183/1276 Combination Sander -5- 110/220V Operation SECTION 2: CIRCUIT REQUIREMENTS The 1 HP motor will draw 12 amps at 110V and 6amps at 220V. A 15-amp fuse or circuit breakershould be used when fusing this combinationsander. Circuits rated any higher are not ade-quate to protect the motor from po...

G1183/1276 Combination Sander -7- SECTION 3: GENERAL INFORMATION Grizzly Industrial, Inc. is proud to offer the ModelG1183 6" x 48" – 12" Disc Combination Sanderand its slower-speed version, the Model G1276.This saw is a part of Grizzly’s growing family offine woodworking machinery. When...

-8- G1183/1276 Combination Sander Unpacking The Combination Sander is shipped from the fac-tory in a carefully packed carton. If you find themachine to be damaged after you’ve signed fordelivery and the truck and driver are alreadygone, you will need to file a freight claim with thecarrier. Save the...

G1183/1276 Combination Sander -9- Clean Up The unpainted surfaces are coated with a waxyoil to protect it from corrosion during shipment.Remove this protective coating with a solventcleaner or citrus-based degreaser. Avoid chlo-rine-based solvents as they may damage paintedsurfaces should they come ...

G1183/1276 Combination Sander -11- Disc Table The disc table adjusts to allow you to sand yourwork at angles from -20° up to 45°. To install thedisc table: 1. Loosen the two star knobs at either end ofthe disc table base until they reach theends of their threaded rods. 2. Move the sliding rails and ...

-12- G1183/1276 Combination Sander SECTION 5: ADJUSTMENTS Proper adjustment of the Combination Sander isessential to ensure its optimum performance. Theadjustments covered in this section are easilyaccomplished. Tables Tables should be square in both planes to exe-cute precise work. Procedures for a...

-13- Figure 11. Adjusting disc table stops. G1183/1276 Combination Sander 6. Repeat this procedure with the 45° stop. You’ll need a known 45° angle, such as aspeed square or the head of a combinationsquare to check accuracy. Figure 10. Adjusting belt table stops. To Adjust the Disc Table Positive St...

G1183/1276 Combination Sander -17- SECTION 6: OPERATIONS The aluminum disc accepts 12" diameter cloth orpaper-backed PSA sanding discs. The beltsander requires a 6" x 48" sanding belt. For discor belt sanding, we recommend a 100-grit (medi-um) material for general sanding chores, a 60-gr...

-20- G1183/1276 Combination Sander SECTION 7: MAINTENANCE Tables The tables and other non-painted surfaces on theModel G1183 and G1276 should be protectedagainst rust and pitting. Wiping the sander cleanafter every use ensures that moisture from wooddust isn’t allowed to trap moisture against bareme...

-24- G1183/1276 Combination Sander Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1183 COMBINATION SANDER MACHINE DATA SHEET Design Type .................................................................................................... Ben...

G1183/1276 Combination Sander -25- Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1276 COMBINATION SANDER MACHINE DATA SHEET Design Type ....................................................................................................Benc...

-26- G1183/1276 Combination Sander MAIN UNIT PARTS DIAGRAM

G1183/1276 Combination Sander -27- PARTS LIST 001 P1183001 STAND 002 P1183002 BASE PLATE 003 PB17M HEX BOLT M8-1.25 X 16mm 004 P1183004 COVER SCREW 005 PW03 FLAT WASHER #10 006 P1183006 COVER LOCK 007 PC400B CAPACITOR-BIG OD 008 P1019090A SWITCH 008A P1019090B PLASTIC SWITCH COVER 009 P1183009 SWITC...

G1183/1276 Combination Sander -29- MOTOR UNIT PARTS DIAGRAM 068 P1183068 COVER 070 P1183070 PLATE 071 PSB14M CAP SCREW M8-1.25 x 20 072 P1183072 KNURLED CHECK NUT 073 P1183073 KNURLED BOLT 074 P1183074 SPRING 075 P1183075 LEVER HOLDER 076 PRP33M ROLL PIN 6 x 50mm 077 PN08 HEX NUT 3 ⁄ 8 "-16 078 ...

-30- G1183/1276 Combination Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or...

G1183/1276 Combination Sander CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw...