Transition Networks SSEFE10XX-10X - Manual
Transition Networks SSEFE10XX-10X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation; Power the Media Converter
- Page 3 – Install the Fiber Cable; Install the Copper Cable; AutoCrossTM; Operation; Status LEDs
- Page 4 – Fiber Cable; Cable Specifications; Copper Cable
- Page 5 – Technical Specifications; Troubleshooting
- Page 6 – Contact Us
- Page 7 – Compliance Information
* Typical maximum cable distance. Actual distance is dependent upon the
physical characteristics of the network. (TX) = transmit, (RX) = receive
The SSEFE10xx-10x media converter is designed to be installed in pairs, where one
is the
local
media converter and the other is the
remote
. For example, a local
SSEFE1011-100 converter is connected, via fiber, to a remote SSEFE1011-100
converter.
For a
single fiber network
, a local SSEFE1029
-100
is connected, via fiber, to a
remote SSEFE1029
-101
converter.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .5
Cable Specifications . . . . . . . . . . .6
Technical Specifications . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . .9
Compliance Information . . . . . . .12
User’s Guide
SSEFE10xx-10x
Stand-Alone Media Converter
• Switchable Ethernet and Fast Ethernet
• 10 Mb/s Copper to Fiber
• 100 Mb/s Copper to Fiber
Transition Networks SSEFE10xx-10x series
Ethernet / Fast Ethernet media converter is a
10Mbps or 100Mbps switch-selectable media
converter. Both the copper and fiber links operate at the same speed setting via a
hard set with a dip switch, so the media converter operates at either 10 Mb/s
copper to fiber or 100 Mb/s copper to fiber.
Part Number
Port One -
Twisted-Pair
Copper
Port Two -
Fiber Optic
SSEFE1012-100
RJ-45, 100 m (328 ft)*
ST, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
SSEFE1014-100
RJ-45, 100 m (328 ft)*
SC, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
SSEFE1015-100
RJ-45, 100 m (328 ft)*
SC, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
SSEFE1022-100
RJ-45, 100 m (328 ft)*
ST, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
SSEFE1029-100
RJ-45, 100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
single fiber, 20 km (12.4 miles)*
SSEFE1029-101
RJ-45, 100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
single fiber, 20 km (12.4 miles)*
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 SSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation The Link Pass-Through and speed switches are located on the side of the media converter. Use a small screwdriver to set the recessed switches. Set Link Pass-Through (switch 1) Switch 1 sets the...
4 SSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued Install the Fiber Cable The SSEFE10xx-10x is designed to be installed in pairs over the fiber link,where one is the local media converter and the other is the remote. 1. Locate or ...
6 SSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Fiber Cable Bit Error Rate: <10-9 Single mode: 9 µm SSEFE1012-100 1310 nm single mode Fiber-optic Transmi...
