Transition Networks SSDTF1012-105 - Manual
Transition Networks SSDTF1012-105 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Optional Accessories; (includes universal internal power supply); Installation; Set the hardware/software jumper; The device mode is determined by the
- Page 3 – Set the loop-back switch; CL; fiber; Select T1 configuration
- Page 4 – Settings for T1 configuration
- Page 5 – Install the copper cable; Install the fiber cable; Operation; Remote management function; Power the device
- Page 6 – Fiber cable; Fiber cable
- Page 8 – Contact Us; Technical support
- Page 9 – Compliance Information; FCC regulations
Installation . . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . . .9
Cable Specifications . . . . . . . . . . . . .10
Technical Specifications . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . .13
Compliance Information . . . . . . . . .16
* Typical maximum cable distance.
(Actual
distance is dependent upon the physical
characteristics of the network.)
Note:
The SSDTF10xx-10x requires a CSU
between the device and the Public Telephone
Network.
SSDTF1027-105
RJ-45
1.5 km
(5,000 feet)
*
ST, 1300 nm multimode
5 km
(3.1 miles)*
Part Number
Port One - Copper
Port Two - Duplex Fiber-Optic
SSDTF1011-105
RJ-45
1.5 km
(5,000 feet)
*
ST, 850 nm multimode
2 km
(1.2 miles)
*
SSDTF1012-105
RJ-45
1.5 km
(5,000 feet)
*
ST, 1310 nm single mode
8 km
(4.8 miles)
*
SSDTF1013-105
RJ-45
1.5 km
(5,000 feet)
*
SC, 850 nm multimode
2 km
(1.2 miles)
*
SSDTF1014-105
RJ-45
1.5 km
(5,000 feet)
*
SC, 1310 nm single mode
20 km
(12.4 miles)
*
SSDTF1015-105
RJ-45
1.5 km
(5,000 feet)
*
SC, 1310 nm single mode
40 km
(24.8 miles)
*
SSDTF1016-105
RJ-45
1.5 km
(5,000 feet)
*
SC, 1310 nm single mode
60 km
(37.3 miles)
*
SSDTF1017-105
RJ-45
1.5 km
(5,000 feet)
*
SC, 1550 nm single mode
80 km
(49.7 miles)
*
SSDTF1018-105
RJ-45
1.5 km
(5,000 feet)
*
MT-RJ, 1300 nm multimode
2 km
(1.2 miles)
*
SSDTF1022-105
RJ-45
1.5 km
(5,000 feet)
*
ST, 1310 nm single mode
15 km
(9.3 miles)
*
SSDTF1025-105
RJ-45
1.5 km
(5,000 feet)
*
MT-RJ, 1310 nm single mode
20 km
(12.4 miles)
*
User’s Guide
SSDTF10xx-10x
Stand-Alone Devices
•
T1 / E1 with Remote Management
•
Copper to Fiber
Transition Networks SSDTF10xx-10x series
Devices encode and decode T1 or E1 twisted-pair
copper signals over fiber optic cable to extend the
distance and transmission reliability of high-speed
T1 or E1 data traffic. The device is framing independent
(as ESF vs. D4)
and supports all
common line codes
(e.g., AMI, B8ZS, HDB3)
.
The SSDTF10xx-10x is designed to be installed in pairs. For example, install one
SSDTF1011-105 as the “local ” Device and another SSDTF1011-105 as the “remote ”
Device.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 SSDTF10xx-10x (TX) = transmit (RX) = receive * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. ** SSDTF1029-105 and -106 are intended to be installed in the same network where one is the local device and the other is the remote device....
4 SSDTF10xx-10x Installation -- Continued Set the loop-back switch Hardware mode: The loop-back switch is located on the front panel of the device and is used forinstallation and network debugging procedures. To set the switch, use a small flat-blade screwdriver or asimilar device (see the drawing t...
6 SSDTF10xx-10x Installation -- Continued Settings for T1 configuration (right switch set, SW 1) T1/long-haul signal Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the drawing below). Use switches 1 and 2 on the right switch set to select the proper network cablesetti...
