Transition Networks SBFTF1017-120 - Manual
Transition Networks SBFTF1017-120 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – c h a s s i s v e r s i o n; Copper and Fiber Ports; Part Number; Installation; Set the Dip Switches; only; Switches 2
- Page 3 – ALL; ONLY
- Page 4 – Connect the Fiber Cable; Connect the Twisted-Pair Copper Cable; AC
- Page 5 – Status LEDs; Speed LED; Operation; Product Features; Distance Extension
- Page 6 – Rate Conversion; disable; AutoCrossTM; Cable Specifications; Fiber Cable
- Page 7 – Copper Cable; Technical Specifications
- Page 8 – Troubleshooting; Compliance Information
- Page 9 – Contact Us
Part Number
Copper -
five (5) ports
10Base-T/100Base-TX
Duplex Fiber-Optic -
one (1) port
100Base-FX
SBFTF1011-120
RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
SBFTF1013-120
RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
SBFTF1014-120
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
20 km (12.4 miles)*
SBFTF1015-120
(long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
40 km (24.8 miles)*
SBFTF1016-120
(extra long haul)
RJ-45
100 m (328 ft)*
SC, 1310 nm single mode
60 km (37.2 miles)*
SBFTF1017-120
(long wave length)
RJ-45
100 m (328 ft)*
SC, 1550 nm single mode
80 km (49.7 miles)*
SBFTF1018-120
RJ-45
100 m (328 ft)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
SBFTF1025-120
RJ-45
100 m (328 ft)*
MT-RJ, 1310 nm single mode
5 km (3.1 miles)*
User’s Guide
SBFTF10xx-12x
Stand-Alone Media Converter
•
Copper to Fiber
•
10/100 Bridging 6-Port
•
(5 copper / 1 fiber)
•
10/100Base-TX to 100Base-FX
The SBFTF10xx-12x 6-port Ethernet/fast Ethernet bridging media converter allows
connection of 10Base-T Ethernet and/or 100Base-TX fast Ethernet twisted-pair
copper network devices to network devices on a 100Base-FX fast Ethernet fiber
network.
* T y p i c a l m a x i m u m c a b l e d i s t a n c e .
Actual distance is dependent upon the
physical characteristics of the network.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .8
Cable Specifications . . . . . . . . . .11
Technical Specifications . . . . . . .13
Troubleshooting . . . . . . . . . . . . .14
Compliance Information . . . . . . .15
Contact Us . . . . . . . . . . . . . . . . .16
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 SBFTF10xx-12x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 * Typical maximum cable distance. Actual distance is dependent upon thephysical characteristics of the network. (TX) = transmit (RX) = receive ** SBFTF1029- 120 and - 121 are intended to be installed in the...
4 SBFTF10xx-12x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued Set the Dip Switches -- Continued NOTE: Dip switch 4 (in the “SW” set) applies to fiber port 1 (F1). 4. Fiber Mode (Fiber Port 1) Up (Full-Duplex) - The cable distances for fiber p...
6 SBFTF10xx-12x 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued • If half-duplex mode is used, refer to the 512-Bit Rule (see page 9). • If full-duplex mode is used, the 512-Bit Rule does not apply. The cable lengths are constrained by the cabl...
