Transition Networks SAPTF33xx-110 - Manual
Transition Networks SAPTF33xx-110 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Grounding the Media Converter; Installation; Installing the Cable -- Standard Configuration; Fiber
- Page 3 – Operation; Power the Media Converter; AC; Status LEDs; ACT
- Page 4 – Cable Specifications; Copper Cable
- Page 5 – Technical Specification; RJ-11C Connector Specification; Troubleshooting; YES
4
SAPTF33xx-1xx
24-hour Technical Support:
1-800-260-1312
-- International:
00-1-952-941-7600
SAPTF33xx-1xx in the Network
Standard Configuration
One Unit A device (SAPTF33xx-100) and one Unit B device (SAPTF33xx-110)
are required for the standard configuration. The Unit A device is connected to
the Central Office (CO) while the Unit B device is connected to a telephone
device.
Automatic Ring-Down Configuration
Automatic Ring Down (ARD) is a dedicated, point-to-point voice system. When
one telephone is taken off-hook, the other telephone rings, without the need to
dial. Two Unit B devices (SAPTF33xx-110), connected via the fiber ports, are
required for this mode of operation; with a telephone device at each end.
SAPTF33xx-100
Unit A -- Emulates
the telephone device
SAPTF33xx-110
Unit B -- Emulates the
Central Office (CO)
Central Office (CO)
SAPTF33xx-110
Unit B -- Emulates the
Central Office (CO)
SAPTF33xx-110
Unit B -- Emulates the
Central Office (CO)
5
Click the “
Transition Now
” link for a live Web chat.
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the jumpers. Failure to observe this caution could
result in damage to, and subsequent failure of, the media converter.
Setting the Jumpers
1.
Using a small screwdriver, remove the screws that secure the cover to the
media converter and carefully remove the cover.
2.
Locate the jumpers on the circuit board.
3.
Using small needle-nosed pliers or similar device, move the jumper to the
desired position. (Refer to the drawings below.)
4.
Carefully replace the cover on the media converter and replace the
screws to secure the cover.
Standard / Automatic Ring-Down
The jumper labeled “JP1” is used to switch between the Standard or Automatic
Ring-Down configuration and is located on the
top
circuit board of
Unit B
(SAPTF33xx-110)
.
The drawing below illustrates the jumper settings.
•
Set jumper JP1 on the Unit B device to the
Standard
setting when
using the Standard configuration (described on page 4).
•
Set jumper JP1 on
both
Unit B devices to the
Automatic Ring-Down
s e t t i n g w h e n u s i n g t h e A u t o m a t i c R i n g - D o w n c o n f i g u r a t i o n
(described on page 4).
US / EU Telephone Regulation
The jumper labeled “US EU” is used to switch between the US or EU
telephone configuration and is located on the
top
circuit board of
Unit A
(SAPTF33xx-100)
. This feature is required to comply with the EU TBR21
telephone regulation. The jumper has been set at the factory to the US setting
as the default.
The drawing below illustrates the jumper settings.
•
Set jumper “US EU” on the Unit A device to the
US
setting if the
device is to be used with US-based telephone systems.
•
Set jumper “US EU” on the Unit A device to the
EU
setting if the
device is to be used with European-based telephone systems.
Standard
1
3
Automatic
Ring-Down
1
3
JP1
JP1
US Setting
EU Setting
US
EU
US
EU
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Installation -- Continued Grounding the Media Converter The SAPTF33xx-1xx single-slot chassis comes equipped with grounding lugslocated on the back panel. They require a grounding conductor wireterminated with a two-hole, compression-type, grounding connector . The grounding wire -- which must be a ...
8 SAPTF33xx-1xx 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued Installing the Cable -- Automatic Ring-Down Configuration NOTE: Both Unit B’s MUST be configured for Automatic Ring-Down (see page 4). Fiber 1. Locate or build fiber cable with mal...
10 SAPTF33xx-1xx 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Operation - Continued Loop-Start Operation Loop-Start Service -- commonly known as “Plain Old Telephone Service”(POTS) -- is the primary analog signaling method used between telephoneswitches such as the C...
