Transition Networks P332MF - Manual

Before you Start 8 Quick Start for Hardware Installation: P332MF Stackable Switch Building a stack Follow the guidelines in this section in order to build a working stack using any combination of the following devices: ● P330 series ● P330-ML series ● G700 ● P330 series 1. Add only a single box at a...

Before you Start 10 Quick Start for Hardware Installation: P332MF Stackable Switch Stack Master election rules Table 5 lists the switches in order of election priority from highest to lowest. Note: Note: If there are two switches with the same firmware version and the same election priority, the swi...

Issue 1 September 2005 13 Chapter 2: Unpack the Device ELECTROSTATIC ALERT: ! ELECTROSTATIC ALERT: Wear an anti-static wrist ground strap whenever you handle components of a P330. Connect the strap to an approved ground, such as an unpainted metal surface. Equipment Open the box that contains the P3...

Unpack the Device 14 Quick Start for Hardware Installation: P332MF Stackable Switch Documentation ● Avaya P332MF Quick Start Guide (this document) ● Avaya P330 Release Notes One RJ45 to DB9F Adapter One DB25M Adapter Four (4) 5/16" Round Head Screws Four (4) Washers Four (4) stand-off feet

Documentation Issue 1 September 2005 15 ● Avaya P330 Documentation and Utilities CD (see detail below) ● Avaya Communication Warranty and License Agreement Avaya P330 Documentation and Utilities CD The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for use with ...

Issue 1 September 2005 # Chapter 3: Mount the Device You can mount the P330 in a rack. The P330 chassis fits in most standard 19-inch racks. It is 2U (3.5”, 88 mm) high. Before you Install the P330 in a Rack ● Disconnect all cables from the unit before proceeding with the rack installation. ● When i...

Issue 1 September 2005 23 Chapter 5: Prepare for Configuration This chapter provides information on preparing the P330 for configuration, and discusses the following topics: ● Establishing a Console Connection ● Assigning a P330 IP Stack Address ● Establishing a Telnet Connection ● Configuring the S...

Prepare for Configuration 24 Quick Start for Hardware Installation: P332MF Stackable Switch 1. Use the serial cable supplied to attach the RJ-45 console connector to the Console port of the active P330 switch. Connect the DB-9 connector to the serial (COM) port on your PC/terminal. - The master P330...

Establishing a Telnet Connection Issue 1 September 2005 25 4. At the prompt, type: set interface inband <vlan> <ip_address> <netmask> Replace <vlan> , <ip_address> and <netmask> with the VLAN, IP address, and net mask of the stack. 5. Press Enter to save the IP ad...

Prepare for Configuration 26 Quick Start for Hardware Installation: P332MF Stackable Switch Configuring the Switch This section describes the procedures for the first-time configuration of the Avaya P330. The factory defaults are set out in detail in the tables included in this chapter. You may conf...

Configuring the Switch Issue 1 September 2005 27 5. Press Enter to save the destination and gateway IP addresses. Avaya P330 Default Settings If you wish to change the default parameters shown and configure the mandatory parameters, we recommend that you use the Command Line Interface (CLI). For fur...

Issue 1 September 2005 29 Chapter 6: Device Manager This chapter describes the installation procedures for the Device Manager of the Avaya P330. Overview The Device Manager provides the following: ● Managing and monitoring Power over Ethernet. ● Device Configuration - Viewing and modifying the diffe...

Device Manager 30 Quick Start for Hardware Installation: P332MF Stackable Switch Configuring the Device Manager You can configure several Device Manager parameters using the CLI. These parameters include the time-out and retries parameters, the location of the Web server that provides the help files...

Device Manager 32 Quick Start for Hardware Installation: P332MF Stackable Switch Figure 8: Device Manager 3. If you do not have the Java plug-in installed, follow the instructions on the Welcome page for a variety of options to install the plug-in (see Installing the Java Plug-in ). Installing the J...

Installing the On-Line Help and Java Plug-In on your Web Site Issue 1 September 2005 33 4. Browse to the embweb-aux-files\ folder on the CD. 5. Double-click plugin_a_b_c.exe (a, b and c are the version numbers of the plug-in). 6. Follow the on-screen instructions. Install from the Avaya Web Site Cli...