Page 3 - Content
1 Content INTRODUCTION .............................................................................. 3 Features ...................................................................................................................3 Software Feature.........................................................
Page 5 - Introduction; Features
3 Introduction The 8 10/100/1000T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch that can be used to build high-performance switched workgroup networks. The switch is targeted at workgroup or department. The 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch featu...
Page 6 - Software Feature
4 VLAN Port Based VLAN IEEE 802.1Q VLANs. Up to 256 groups Support DHCP client Support Class of Service Support Spanning Tree 9K Jumbo Frame support Software Feature Management Web Management Firmware update Web UI firmware update System default One default button for system default Default IP: 192....
Page 9 - Hardware Description; functional overview on certain switch.; Physical dimension; Managed Switch’s physical dimension is 217 x 140 x 43 mm (L x W x H).; Front Panel; to the LED Indicator section for LED description.
7 Hardware Description This section mainly describes the hardware of the 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web-Smart Switch and gives a physical and functional overview on certain switch. Physical dimension The 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Man...
Page 10 - crossover cabling.; Rear Panel
8 Switch RJ-45 Ports (Auto MDI/MDIX): 7x 10/100/1000 N-way auto-sensing for 10Base-T, 100Base-TX or 1000Base-T connections. In general, MDI means connecting to another Hub or Switch while MDIX means connecting to a workstation or PC. Therefore, Auto MDI/MDIX would allow connecting to another Switch ...
Page 11 - LED Indicators; LED
9 LED Indicators The LED Indicators display real-time information of systematic operation status. The following table provides descriptions of LED status and their meaning. LED Panel of 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch LED Status Color Description On Green...
Page 12 - Desktop Installation; Attaching Rubber Pads; Power On
10 Blinks Orange Collision of Packets occurs in the port Off -- Half-duplex mode or no device attached On Green The port is successfully connecting with the device Blinks Green The port is receiving or transmitting data LNK /ACT (MINI GBIC) Off -- No data transmitted or no device connected The Descr...
Page 14 - Network Application; address table (8k MAC address) and high performance, it is ideal for; Small Workgroup
12 Network Application This section provides user a few samples of network topology in which the switch is used. In general, the 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch is designed as a segment switch. That is, with its address table (8k MAC address) and high per...
Page 15 - Segment Bridge; between two switches depends on the type of fiber transceiver.
13 Segment Bridge For enterprise networks where large data broadcasts are constantly processed, this switch is an ideal solution for department users to connect to the corporate backbone. Use two 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch with PCs, print server, and...
Page 17 - Web-Based Management; About Web-based Management; as Microsoft Internet Explorer.; System Login; The default value is as below:
15 Web-Based Management This section introduces the function configuration of the 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch. About Web-based Management On the CPU board of the switch there is an embedded HTML web site residing in flash memory, which offers advanced...
Page 18 - Launch the Internet Explorer; SFP/RJ45 Combo port Web Managed Switch, and then press “Enter”; Login screen will appear right after; System Configuration; system can be configured as well.
16 1. Launch the Internet Explorer 2. Key in “http://” + “IP Address” of the 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch, and then press “Enter” 3. Login screen will appear right after 4. Key in the password(The default password is “root”) 5. And then, click Apply , ...
Page 19 - time the client/switch boots and the lease is 50% or more passed, the; DHCP Enable: To enable DHCP Client Function
17 time the client/switch boots and the lease is 50% or more passed, the client/switch will attempt to renew the lease. At 87.5% of the lease completion, the client/switch will attempt to contact any DHCP server for a new lease System Configuration interface DHCP Enable: To enable DHCP Client Functi...
Page 20 - Port Configuration; Mode: Set the Auto Speed, 1000 Full mode of the port
18 remote management that include telnet, SNMP, and Web browse the switch only when the port of VLAN group ID is equal to the Management VLAN ID Name: the name of the switch Password: Web GUI login password. The default password is root Inactivity Timeout: The web connection timeout time And then, c...
Page 21 - Statistics Overview; Press; button to clean all counts
19 Port Configuration interface Statistics Overview The following information provides the current port statistic information Press Clear button to clean all counts And then, click Refresh to get the new setting information as below: Statistics Overview interface
Page 22 - Statistics Detail; VLAN Setting
20 Statistics Detail The following information provides statistic detail information of statistic on each port, and simply selecting the port to viewing the statistic information. Press Clear button to clean all counts And then, click Refresh to get the new setting information as below: Statistics D...
Page 23 - VLAN Port Setting; Click; PVID: Enter the Port VLAN ID
21 And then, click Apply to bring up the configuration interface as below: VLAN Setting interface VLAN Port Setting Click VLAN Port Setting to bring up the configuration interface for adjusting the VID Setting PVID: Enter the Port VLAN ID Awareness: Enable the awareness that ports will strip the VLA...
Page 24 - After that, click Apply to apply the configuration; Port Trunk
22 in transmitted frames Frame Type: To set the outgoing frames Tagged: Outgoing frames with VLAN-Tagged All: All type of frames After that, click Apply to apply the configuration Or, click Refresh to reset the configuration before applying VLAN Port Setting interface Port Trunk Port trunk allows mu...
Page 25 - LACP Setting; Protocol Enable: To enable the LACP protocol of the port; And then, click Apply to apply the configuration
23 Grouping the members of Trunk. Normal means the port is not trunk port And then, click Apply to apply the configuration Or, click Refresh to reset the configuration before applying Port Trunk interface LACP Setting The Link Aggregation Control Protocol (LACP) provides a standardized means for exc...
Page 26 - Or, click Refresh to reset the configuration before applying; LACP Status
24 Or, click Refresh to reset the configuration before applying LACP Setting interface LACP Status When the LACP aggregator had been setup, the LACP status information will display as below:
Page 27 - Spanning Tree; device that is running STP or RSTP protocol.; RSTP System Configuration
25 LACP Status interface Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto detect the connected device that is running ST...
Page 28 - the port begins forwarding.; Force version: Select the RSTP default protocol. Normal means RSTP; protocol. Compat is for compatibling with STP protocol.
26 lowest value has the highest priority and is selected as the root. If the value has being changed, user has to reboot the switch. The value must be multiple of 4096 according to the protocol standard rule. Hello Time (1-10): The scale of 1~10 sec will be set as a period of time that how often the...
Page 29 - RSTP Port Configuration; Protocol Enable: To enable or disable the port protocol; Spanning Tree Status; Bridge information will display as below:
27 RSTP Port Configuration Protocol Enable: To enable or disable the port protocol Edge: The port directly connected to end stations cannot create bridging loop in the network. To configure the port as an edge port, mark the port Path Cost: The cost of the path to the other bridge from this transmit...
Page 31 - Parameters Configuration; Reauthentication Enable: To enable the re-authentication mode; which clients connected must be re-authenticated
29 Or, click Refresh to reset the configuration before applying 802.1X Configuration interface Parameters Configuration Reauthentication Enable: To enable the re-authentication mode Reauthentication period (1~3600 seconds): Set the period of time after which clients connected must be re-authenticate...
Page 32 - QoS Setting; And then, click Apply to apply the configuration
30 QoS Setting Configuring QoS mode of the port and per port priority, TOS and COS priority setting. Mode: Select the QoS mode – port, DSCP, or vlantag Port Priority: Select the priority level – low, normal, medium, or high And then, click Apply to apply the configuration Or, click Refresh to reset ...
Page 33 - the TOS value of received IP packet is 25(priority = high), and then the
31 QoS Configuration interface Click DSCP Mapping to enter TOS priority configuration interface DSCP [0- 63]: The system provides 0~63 TOS priority level. When the IP packet is received, the system will check the TOS level value in the IP packet that has received. For example: user set the TOS level...
Page 35 - System Restart; Factory Default; Firmware Upload; Browse
33 System Restart Reboot the switch in software reset. All the configurations will be reminded Click Yes to restart the system System Restart interface Factory Default Reset switch to default configuration Click Yes to reset the all configuration to the default value Factory Default interface Firmwa...
Page 36 - Upload; Configuration File Transfer
34 And then, press Upload to update the firmware Firmware Upload interface Configuration File Transfer The system provides the Web GUI configuration upload function which would allow the user to backup the switch configuration. Click Browse to locate the path for Uploading And then, press Upload to ...
Page 37 - Troubleshooting; Incorrect connections; module should be match.; Faulty or loose cables; Category 3, 4 or 5 cable for 10Mbps connections or
35 Troubleshooting This section is intended to help user solve the most common problems on the 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch with. Incorrect connections The switch port can auto detect straight or crossover cable when link switch with other Ethernet dev...
Page 38 - Improper Network Topologies; severely impact the network performance.; Diagnosing LED Indicators
36 100 Ω Category 5 cable for 100Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet). Gigabit port should use Cat-5 or cat-5e cable for 1000Mbps connections. The length does not exceed 100 meters. Improper Network Topologies It is impor...
Page 39 - Technical Specification; Standard
37 Technical Specification This section provides the specifications of 8 10/100/1000Base-T with 1 1000Base-X SFP/RJ45 Combo port Web Managed Switch with. Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000Base-T IEEE 802.3z Gigabit Fiber IEEE 802.3x Flow Cont...
Page 41 - FCC Class A; Safety; UL
39 Operating Humidity 10% to 90% (Non-condensing) EMI FCC Class A CE Safety UL cUL 10900 Red Circle Drive Minnetonka, MN 55344 Tel.: +1.952.941.7600 [email protected]
