Transition Networks E-PSW-TX-02 - Manual
Transition Networks E-PSW-TX-02 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – 00BASE-FX Cable and Connector Specifications; Transition Networks’
- Page 3 – ETHERNET CABLE SPECIFICATIONS; 0BASE-T CABLE SPECIFICATIONS; Maximum Cable Distance:; Maximum Cable Distance:; Table of Contents; WARRANTY STATEMENT
- Page 4 – OR
- Page 5 – The Evolving Ethernet Network; Warranty Statement
- Page 6 – Network Flexibility; Protocol Compatible; Fault Isolation; YES; Technical Support Contact
- Page 7 – Connectors; NOTE: The port LED indicators provide separate data for each port.; Switches (at surface opposite connectors); Resets hardware to initial operating condition.
- Page 8 – Powering Transition Networks’ Pocket Switch
- Page 9 – Installing Network Cable; Connecting Fiber Cable to TX/RX Connectors; OPTICAL POWER LOSS BUDGET; FAST ETHERNET COLLISION DOMAIN; Locate or build 100BASE-FX cables with the following; MAC Address Table; CSMA; Existing 10 Mb/s Network
- Page 10 – Doubling Bandwidth by Installing Full-Duplex; dedicated twisted; Microsegmented Ethernet Link is Full-Duplex; 0BASE-T AND THE ETHERNET COLLISION DOMAIN
- Page 11 – Install Transition Networks' Pocket Switch; Straight-Through Cable
- Page 13 – ASSIGNING SEGMENT NUMBERS
- Page 14 – Category 3 or Category 5
- Page 15 – Setting DIP Switch; Locate the DIP switch at the back of the Transition Network’s; Class I and Class II Fast Ethernet Repeaters; Install Install Transition Networks' Pocket Switch
- Page 16 – SITE CONSIDERATIONS; Unpacking; the; Transition Networks’ Pocket Switch; Item; Installing on Flat, Stable Surface
TRANSITION NETWORKS’ POCKET SWITCH
TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3, IEEE 802.3u
Dimension
4.75" X 5.75" X 1.0"
(120mm x 146mm x 25mm)
Power Supply
NOTE:
Replace power supply only with the equivalent input rating (see below) and
output rating (regulated 12VDC at 1.5 A).
TN PN
Requirement
Location
3507
240 volts, 50 hertz
United Kingdom
3342
230 volts, 50 hertz
Europe
3340
120 volts, 60 hertz
USA/Canada/Mexico
3346
100 volts, 50-60 hertz
Japan
3511
240 volts, 50 hertz
Australia
3537
(with power cord: 3522)
South Africa
Environment
Temperature:
0-50°C (32° to 122° F )
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Lifetime
Transition Networks’
29
For assistance in installing, using, or
maintaining the TRANSITION Networks
Pocket Switch, contact TRANSITION
Networks Technical Support
at:
(800) 260-1312
or contact your local distributor.
33015.B
(E-PSW-TX-02, E-PSW-FX-02)
Pocket Switch
Transition Networks’
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
100BASE-FX Cable and Connector Specifications The physical characteristics of the 100BASE-FX cable must meet or exceed IEEE802.3u 100BASE-FX specifications. 100BASE-FX CABLE SPECIFICATIONS Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber Optional: 100 / 140 µm multimode fiber 85 / 125 µm...
ETHERNET CABLE SPECIFICATIONS 10BASE-T/100BASE-TX Cable and ConnectorSpecifications The physical characteristics of the 10BASE-T /100BASE-TX cable andconnectors must meet or exceed IEEE 802.3/802.3u specifications. 10BASE-T CABLE SPECIFICATIONS Category 3 wire or better is required; category 5 wire ...
1. INTRODUCTION This guide is intended for the system or network administratorresponsible for installing and monitoring a Transition Networks’ pocketswitch. A working knowledge of local area network (LAN) operations,including familiarity with communications protocols used oninterconnected LANs, is a...
