Page 2 - COMPLIANCE INFORMATION
COMPLIANCE INFORMATION UL Listed C-UL Listed (Canada)CISPR/EN55022 Class AFCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 ofthe FCC rules. These limits are designed to provide reasonable protection against harmful i...
Page 3 - Table of Contents; MULTICHANNEL MEDIA CONVERTER
Table of Contents 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1 1.1 Multichannel Media Converter Models . . . . . . . . . . . . 1.2 1.2 Media Converter Channels . . . . . . . . . . . . . . . . . . . . . 1.2 1.3 Channel Switches . . . . . . . . . . . . . . . . ....
Page 5 - INTRODUCTION
1. INTRODUCTION The TRANSITION Networks METTF10xx (Ethernet ™ ) and MFETF10xx (Fast Ethernet ™ ) series Multichannel Media Converters connect twisted-pair copper cable to fiber-optic cable in separate copper-to-fiber mediaconverter pairs, called channels. The network administrator can select aMultic...
Page 7 - INTRODUCTION
1.3 Channel Switches Full-duplex/half-duplex mode selectionswitches (DIP switches #1-6) allow thenetwork administrator to set EACH mediaconverter channel, separately, either to full-duplex or to half-duplex. The Link Test switch (DIP switch #7)enables or disables the Missing Link Testfeature for a b...
Page 8 - Connections to Management Module; Management Module LEDs; Serial Port
1.6 Multichannel Media Converter ManagementModule TRANSITION Networks Multichannel Media Converters are shipped witha Management Module installed and functional. Embedded SNMPsoftware in the Management Module allows network management of theMultichannel Media Converter. Connections to Management Mod...
Page 9 - Network RJ-45 Connection
Network RJ-45 Connection The RJ-45 Ethernet connection permits the network administrator tomanage the Multichannel Media Converter using the TRANSITIONNetworks Multiport Management Software graphical interface (or otherSNMP application) at a remote network management station (NMS). TheRJ-45 Ethernet...
Page 11 - INSTALLATION
2 INSTALLATION Direction for installing the TRANSITION Networks Multichannel MediaConverter is provided in the pages that follow. 2.1 Preparing the Site ..................................................................2.2 2.2 Unpacking METTF10xx, MFETF10xx Equipment ....................2.3 2.3 Inst...
Page 12 - Preparing the Site
2.1 Preparing the Site Consider the following when choosing a site for the Multichannel MediaConverter: • Select a site that provides conditions that conform to theenvironmental requirements listed in the appendix. • Select a site that is dust-free and moisture-free. • Do not block the ventilation o...
Page 13 - Unpacking METTF10xx, MFETF10xx Equipment; INSTALLATION
2.2 Unpacking METTF10xx, MFETF10xx Equipment Use the following list to verify the shipment: Item Multichannel Media Converter Rack mounting kit Four self-adhesive rubber feet Power Cord Management Control Cable Muliipoint Management Software Disk Redundant Power Supply Module (with Power Cord) User’...
Page 14 - Setting Management Module Jumper
2.3 Installing Optional Redundant Power SupplyModule The standard Multichannel Media Converter is shipped with one MAINPower Supply Module installed at the back of the Multichannel MediaConverter cabinet and with a protective plate covering an installation slotintended for a second, optional BACKUP ...
Page 15 - Installing Power Supply Module
6. Carefully slide the Management Module back into theMultichannel Media Converter. Ensure that the frame of the Management Module runs smoothlybetween the guides at the bottom of the Multichannel MediaConverter. Note a slight resistance just before the ManagementModule frame comes flush with the re...
Page 16 - Installing Multichannel Media Converter at Site; Standard Rack Installation
2.4 Installing Multichannel Media Converter at Site The Multichannel Media Converter can be installed in a standard rack oron a table, shelf, or other stable surface. 2.4.1 Standard Rack Installation NOTE: Installation bracket mounting screws are provided. Rackmountscrews and clip nuts are NOT provi...
Page 17 - Table-Top Installation
2.4.2 Table-Top Installation The Multichannel Media Converter is shipped with four (4) rubber feet foroptional installation on table or other flat, stable surface. CAUTION: Do not place the Multichannel Media Converter on active,heat generating equipment and avoid placing other devices on top of the...
Page 18 - Powering the Multichannel Media Converter
2.5 Powering the Multichannel Media Converter NOTE: The Multichannel Media Converter does NOT have a powerON/OFF switch. Power is applied to, and removed from, the MultichannelMedia Converter by connecting and disconnecting the power cord. NOTE: The Main Power Supply Module and the Redundant (backup...
Page 19 - Connecting Channel Ports to Network; Setting FDX/HDX Channel Configuration Switches
2.6 Connecting Channel Ports to Network Each channel port is connected, using twisted-pair copper and fiber-opticcable, to network devices. 2.6.1 Setting FDX/HDX Channel Configuration Switches FDX/HDX (F(ull-)D(uple)X and H(alf)D(uple)X) refers to the manner inwhich a network device sends and receiv...
Page 20 - Installing Cable
2.6.2 Installing Fiber-optic Cable Refer to the appendix for cable specifications for the 10BASE-FL or the100BASE-FX fiber-optic installation. Installing Cable 1. Locate or build 10BASE-FL-compliant or 100BASE-FX-compliantcables (depending upon Multichannel Media Converter selectedfor the site), wit...
Page 21 - Installing Twisted-Pair Copper Cable
To perform a link test: 1. Verify that all network devices connected to the fiber-optic portson the Multichannel Media Converter are powered ON andoperational. 2. Cycle power to the Multichannel Media Converter by ptessing theRESET botton, if preseny, or bydisconnecting the power cord fromthe extern...
Page 22 - Setting Network Management Parameters; ONLY
2.7 Setting Network Management Parameters CAUTION: IP parameters should be set and/or modified ONLY at the attached terminal Interface. To set the Multichannel Media Converter network parameters: 1. Locate a PC equipped with any terminal emulation program. 2. Connect the Multichannel Media Converter...
Page 27 - OPERATION
3.1 MULTICHANNEL MEDIA CONVERTER 3. OPERATION Daily operation of the TRANSITION Networks METTF10xx, MFETF10xxMultichannel Media Converter requires no network administrator activityexcept the occasional monitoring of status LED indicators at the front ofthe Multichannel Media Converter. Optionally, t...
Page 28 - Using Status LEDs; Power Supply and Link Test Switch LEDs
3.2 METTF10XX, MFETF10XX 3.1 Using Status LEDs Status LEDs monitor Multichannel Media Converter operation. Power Supply and Link Test Switch LEDs LED Color Indicates MAIN Amber The main power supply is functional. Weak/flashing The main power supply Amber is failing or failed. BCKP Green The optiona...
Page 29 - OPERATION; Using a Terminal Emulator
3 OPERATION 3.3 MULTICHANNEL MEDIA CONVERTER 3.2 Using a Terminal Emulator The Multichannel Media Converter Management Module terminalemulator interface permits the network administrator to display statusmessages and to display and to modify selected network settings. CAUTION: IP parameters can be s...
Page 30 - Using Terminal Emulator
3.4 METTF10xx, MFETF10xx Thrn the main menu comes up with the following options: 1. Device status 2. Device control 3. File download (TFTP) Select (1-3): NOTE: The TFTP feature is NOT enabled in the current software version. At the main menu, select 1 to display the device (port(s)) status menu,whic...
Page 35 - MAINTENANCE
4 MAINTENANCE 4.1 MULTICHANNEL MEDIA CONVERTER 4 MAINTENANCE Maintenance direction for the TRANSITION Networks MultichannelMedia Converter provided in this section includes: 4.1 Fault Isolation and Recovery .................................................4.2 4.2 Hardware Replacement Procedures .......
Page 36 - Fault Isolation and Recovery; Is Multichannel Media Converter Receiving Power?
4.1 Fault Isolation and Recovery Determine the answers to the following questions and, where appropriate,take the indicated action(s): 1. Does Multichannel Media Converter Reset Correct theCondition? • Press the RESET button at the front of the MultichannelMedia Converter Management Module for about...
Page 38 - Is Management Connection Good?
4. Is Management Connection Good? If the Management READY LED is OFF: • Ensure that the Management Module is seated firmly in theMultichannel Media Converter. • Ensure that the Management Module is configured properly(See Section 3 INSTALLATION). If the configuration menu isn’t readable or doesn’t a...
Page 39 - Hardware Replacement Procedures; Replacing Management Module
4.2 Hardware Replacement Procedures WARNING: The METTF10xx, MFETF10xx series Multichannel MediaConverter contains no user-serviceable parts. DO NOT, UNDER ANYCIRCUMSTANCES, open and attempt to repair Multichannel MediaConverter equipment. Failure to observe this warning could result inpersonal injur...
Page 40 - Replacing AC Power Supply Module
4.6 METTF10xx, MFETF10xx Hardware Replacement Procedures 4.2.2 Replacing AC Power Supply Module WARNING: DO NOT CONNECT POWER SUPPLY MODULE TO ACPOWER BEFORE INSTALLING IN MULTICHANNEL MEDIACONVERTER. FAILURE TO OBSERVE THIS CAUTION COULD RESULTIN EQUIPMENT DAMAGE AND/OR PERSONAL INJURY OR DEATH. CA...
Page 41 - APPENDIX A; TECHNICAL SPECIFICATIONS; Dimensions; Environment
A.1 APPENDIX A MULTICHANNEL MEDIA CONVERTER TECHNICAL SPECIFICATIONS Dimensions 4 4 . 1 c m w i d e x 2 6 . 5 c m d e e p x 4 . 4 c m h i g h ( 1 7 . 3 ” w i d e x 1 0 . 4 ” d e e p x 1 . 7 5 ” h i g h ) Weight 4.2 kg (9.2 lbs) Power Input Supply Voltage 110-120/200-240 VAC DC, 50 to 60 Hz Power Con...
Page 43 - APPENDIX B; CHANNEL CABLE SPECIFICATIONS; Twisted-Pair Copper Cable; Category 3
B.1 APPENDIX B MULTICHANNEL MEDIA CONVERTER CHANNEL CABLE SPECIFICATIONS The physical characteristics of the media cable must meet or exceed IEEE 802.3 specifications. Fiber-Optic Cable Multimode: 62.5 / 125 µm multimode fiber Optional:100 /140 µm multimode fiber85 /125 µm multimode fiber50 /125 µm ...
Page 44 - Channel Speed; Twisted-Pair Copper Ports; Twisted-Pair Copper Ports
METTF1011 (-120 and -060) Channel Speed 10 Mb/s Fiber-Optic Ports Cable: Multimode fiber-optic Connector Type ST Wavelength 850 nm Transmitter Power -15 dBm Receiver Sensitivity -32 dBm Maximum Loss Budget 18 dB Maximum distance 3 km (1.8 mi) full-duplex Twisted-Pair Copper Ports Cable Category 3 (o...
