Transition Networks CSRFB10XX-100 - Manual
Transition Networks CSRFB10XX-100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation; The 6-position switch
- Page 3 – PointSystemTM
- Page 4 – Install the fiber cable; RX; Install the twisted-pair copper cable; Operation; Status LEDs; LED; Fiber LEDs; Product Features; Link Test button
- Page 5 – • End converter automatically notified of link loss; Product features - continued; Parallel detection; Full duplex network; (A collision domain is; SNMP
- Page 6 – Bandwidth allocation; • 1 Mbps; Copper cable; Cable Specifications; Fiber cable
- Page 8 – Check the center/terminal switch setting on both converters:; YES; Contact Us; Technical support
- Page 9 – Compliance Information; FCC regulations; Warning
User’s Guide
CSRFB10xx-100
Slide-in-Module Media Converter
•
Copper to Fiber
•
10/100 Bridging
(2-Port)
•
10Base-T/100Base-TX to 100Base-FX
The CSRFB10xx-100, 2-port Ethernet/Fast Ethernet
bridging media converter is designed to be installed in
a Transition Networks
PointSystem™
chassis. This
converter connects 10Base-T Ethernet or 100Base-TX
Fast Ethernet twisted-pair copper network converters
to network converters on a 100Base-FX Fast Ethernet fiber network. The CSRFB
includes a status reporting feature for viewing operational parameters only from its
remotely attached CSRFB converter via the fiber connection.
Installation . . . . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . . . .11
Technical Specifications . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . .13
Contact Us . . . . . . . . . . . . . . . . . . .15
Compliance Information . . . . . . . . .16
Part Number
Port One - Copper
10Base-T/100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
CSRFB1011-100
RJ-45
100 m
(328 ft)
*
ST, 1310nm multimode
2 km
(1.2 miles)
*
CSRFB1013-100
RJ-45
100 m
(328 ft)
*
SC, 1310 nm multimode
2 km
(1.2 miles)
CSRFB1014-100
RJ-45
100 m
(328 ft)
*
SC, 1310 nm single mode
20 km
(12.4 miles)
CSRFB1040-100
RJ-45
100 m
(328 ft)
*
SFP Empty Slot
CSRFB1029-100
RJ-45
100 m
(328 ft)
*
SC, 1310nmTX/1550nmRX
20km
(12.4 miles)
CSRFB1029-101
RJ-45
100 m
(328 ft)
*
SC, 1550nmTX/1310nmRX
20km
(12.4 miles)
CSRFB1029-102
RJ-45
100 m
(328 ft)
*
SC, 1310nmTX/1550nmRX
40km
(24.9 miles)
CSRFB1029-103
RJ-45
100 m
(328 ft)
*
SC, 1550nmTX/1310nmRX
40km
(24.9 miles)
Install CSRFB1029-100/101 and CSRFB1029-102/103 single-
fiber optic in the same network where one is the local
(center)
converter and the other is the remote
(terminal)
converter.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Installation CAUTION: Wear a grounding converter and observe electrostatic discharge precautions while handling the media converter. Failure to observe this caution couldresult in damage to or failure of th...
4 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 The Loopback Mode jumper is located on the mediaconverter’s circuit board (labeled ALL= all frames plus errors, Good = Good frames only). See Jumper position to the right. Loopback test The loopback test is...
6 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Install the fiber cable 1. Locate or build IEEE 803.2 ™ compliant 100Base-FX fiber cable with male, two-stranded TX to RX connectors installed at both ends. 2. Connect the fiber cables to the CSRFB10xx-100 ...
