Transition Networks CSEFE10XX-10X - Manual
Transition Networks CSEFE10XX-10X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Set the Hardware / Software Jumper; Power the Media Converter; Installation
- Page 3 – Install the Fiber Cable; Install the Copper Cable; AutoCrossTM; Operation; Status LEDs
- Page 4 – SNMP; Copper Cable; Cable Specifications; Fiber Cable
- Page 5 – Technical Specifications; stand alone version; Troubleshooting; YES
- Page 6 – Contact Us
- Page 7 – Compliance Information; FCC Regulations
User’s Guide
CSEFE10xx-10x
Slide-in-Module Media Converter
• Switchable Ethernet and Fast Ethernet
• 10 Mb/s Copper to Fiber
• 100 Mb/s Copper to Fiber
Transition Networks CSEFE10xx-10x series Ethernet /
F a s t E t h e r n e t m e d i a c o n v e r t e r i s d e s i g n e d t o b e
installed in a Transition Networks
PointSystem™
chassis and is a 10Mbps or 100Mbps switch-selectable
media converter.
Both the copper and fiber links operate at the same speed setting via a hard set with
a dip switch, so the media converter operates at either 10 Mb/s copper to fiber or
100 Mb/s copper to fiber.
* T y p i c a l m a x i m u m c a b l e d i s t a n c e .
Actual distance is dependent upon the
physical characteristics of the network.
(TX) = transmit, (RX) = receive
The CSEFE10xx-10x media converter is designed to be installed in pairs, where
one is the
local
media converter and the other is the
remote
. For example, a local
CSEFE1011-100 converter is connected, via fiber, to a remote CSEFE1011-100
converter.
For a
single fiber network
, a local CSEFE1029
-100
is connected, via fiber, to a
remote CSEFE1029
-101
converter.
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .5
Cable Specifications . . . . . . . . . . .6
Technical Specifications . . . . . . . .8
Troubleshooting . . . . . . . . . . . . . .9
Compliance Information . . . . . . .12
Part Number
Port One -
Twisted-Pair
Copper
Port Two -
Fiber Optic
CSEFE1012-100
RJ-45, 100 m (328 ft)*
ST, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
CSEFE1014-100
RJ-45, 100 m (328 ft)*
SC, 1310 nm single mode
duplex fiber, 20 km (12.4 miles)*
CSEFE1015-100
RJ-45, 100 m (328 ft)*
SC, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
CSEFE1022-100
RJ-45, 100 m (328 ft)*
ST, 1310 nm single mode
duplex fiber, 40 km (24.8 miles)*
CSEFE1029-100
RJ-45, 100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
single fiber, 20 km (12.4 miles)*
CSEFE1029-101
RJ-45, 100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
single fiber, 20 km (12.4 miles)*
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 CSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the jumper or when installing the media converter. Failure to observe this caution could result in ...
4 CSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued Install the Fiber Cable The CSEFE10xx-10x is designed to be installed in pairs over the fiber link,where one is the local media converter and the other is the remote. 1. Locate or ...
6 CSEFE10xx-10x 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 Operation -- Continued SNMP Use SNMP at an attached terminal or at a remote location to monitor themedia converter by monitoring: • Media converter power • Copper link status • Fiber link status • Copper re...
