Makita EBH252U Manual - Free PDF Download

Page 2 - English; SYMBOLS

2 Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points t...

Page 3 - SAFETY INSTRUCTIONS

3 General Instructions – To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol Brushcutter. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. – It is recommended only to le...

Page 4 - Refuelling

Start the Petrol Brushcutter only in accordance with the instructions. – Do not use any other methods for starting the engine!– Use the Petrol Brushcutter and the tools only for such applications as specified. – Only start the Petrol Brushcutter engine, after the entire assembly is done. Operation o...

Page 5 - Method of operation; Kickback; To avoid kickbacks, observe the following:; Maintenance instructions

5 Method of operation – Only use the Petrol Brushcutter in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. – Never cut above waist height.– Never stand on a ladder and run the Petrol Brushcutter.– Nev...

Page 6 - EC-DECLARATION OF CONFORMITY; (See TECHNICAL DATA for the specifications)

EC-DECLARATION OF CONFORMITY Petrol Brushcutter: model EBH252U, EBH253U, EBH252L, EBH253L (See TECHNICAL DATA for the specifications) We declare under our sole responsibility that this product is in compliance with the following Directives, 2000/14/EC, 2006/42/EC. The most important standards applie...

Page 10 - For machines with bike handle models; MOUNTING OF HANDLE; For machines with loop handle

10 CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely. For machines with bike handle models – Loosen knob...

Page 11 - Be sure to use genuine MAKITA cutter blades or; MOUNTING OF PROTECTOR

11 To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA cutter blades or nylon cutting head. – The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone...

Page 12 - MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD; Mounting of cutterblade with the hex wrench still in place

12 Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily. – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench. – Loosen the nut (1) (left-hand thread) with the socket wrench and ...

Page 13 - Inspection and refill of engine oil; Point 1 in Replacement of oil: “Oil gauge”; BEFORE START OF OPERATION

13 Inspection and refill of engine oil – Perform the following procedure, with the engine cooled down.– While keeping the engine level, remove the oil gauge, and confirm that the oil is filled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches t...

Page 14 - REFUELING; Handling of fuel; Fuel; Point 2 in Replacement of oil: “If oil spills out”

1 REFUELING Handling of fuel It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a...

Page 15 - Attachment of shoulder strap; STARTING; CORRECT HANDLING OF MACHINE; Detachment

15 Attachment of shoulder strap – Adjust the strap length so that the cutter blade will be kept parallel with the ground. For EBH252U, EBH253U NOTE: Be careful not to trap clothing, etc., in the buckle. Observe the applicable accident prevention regulations! STARTING Move at least 3 m away from the ...

Page 16 - Caution during operation:

1 2) Set the I-O switch (1) to OPERATION.3) Choke lever Close the choke lever. Choke opening: – Full closing in cold or when the engine is cold. – Full or half opening in restart just after stop of operation. Note: – If the starter handle is pulled repeatedly when the choke lever remains at “CLOSE” ...

Page 17 - STOPPING; CHECKUP OF LOW-SPEED ROTATION; Attention in Operation; RESHARPENING THE CUTTING TOOL

1 B: Startup after warm-up operation 1) Push the primer pump repeatedly. 2) Keep the throttle lever at the idling position. 3) Pull the recoil starter strongly. 4) If it is difficult to start the engine, open the throttle by about 1/3. Pay attention to the cutter blade which may rotate. STOPPING 1) ...

Page 19 - REPLACEMENT OF ENGINE OIL; Daily checkup and maintenance; SERVICING INSTRUCTIONS

1 REPLACEMENT OF ENGINE OIL Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of replacement. ATTENTION: In general, the engine main unit and engine oil still remain hot just after the engine is stopped. In rep...

Page 20 - CLEANING OF AIR CLEANER; POINTS ON OIL

20 CLEANING OF AIR CLEANER DANGER: INFLAMMABLES STRICTLY PROHIBITED Interval of Cleaning and Inspection: Daily (every 10 operating hours) – Turn the choke lever to the full close side, and keep the carburetor off from dust or dirt. – Remove the air cleaner cover-fixing bolts.– Pull the cover lower s...

Page 22 - fuel tank and; carburetor, and keep it at a dry and clean place.; Fault location; STORAGE; Attention after long-time storage

22 WARNING: When draining the fuel, be sure to stop the engine and confirm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire. ATTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the...

Page 24 - TROUBLESHOOTING

2 TROUBLESHOOTING Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local de...

Page 28 - Makita Corporation