Husqvarna ST 121E/96183000100 - Manual

5 Setup LOOSE PARTS Use the chart below to verify that all parts have been shipped. Description Qty. Carriage bolts Flange nutsWashersKnobChuteDeflector 5 32211 Installing the Handle 1. Remove temporary cable ties holding cables at handle adjustment holes (Figure 2). 2. Release handle adjustment lev...

6 Installing the Discharge Chute 1. Install the chute deflector to the discharge chute using two screws, washers, and deflector knob (Figure 6). 2. Install the discharge chute to the chute base using three screws and nuts. IMPORTANT: Do not overtighten the flange nuts; otherwise you may damage the d...

7 PRODUCT OVERVIEW Product Overview Figure 8 1. Discharge chute2. Chute deflector3. Fuel tank cap4. Primer5. Electric-start button (if equipped) 6. Oil drain plug7. Oil fill cap/dipstick8. Choke lever 9. Ignition key10. Chute rotator handle11. Recoil start handle12. Control bar13. Lights14. Drive si...

8 Operation NOTE: Determine the left and right sides of the machine from the normal operating position. The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thr...

9 OPERATION Starting the Engine 1. Push key in (Figure 10).2. Move choke lever to left position.3. Firmly push in the primer 2 times with your thumb, holding the primer in a for a second before releasing it each time. NOTE: Remove your glove when you push in the primer so that air cannot escape from...

11 OPERATION 2. To raise or lower the angle of the chute deflector, loosen both chute deflector knobs on the chute deflector and move the chute deflector up or down to desired position and retighten knobs (Figure 18). 1. Chute deflector2. Chute deflector knobs Figure 18 2 1 2 Clearing a Clogged Disc...

12 MAINTENANCE Maintenance NOTE: Determine the left and right sides of the machine from the normal operating position. Adjusting the Control Cable CHECKING THE CONTROL CABLE 1. Release the control bar to remove the slack in the control cable (Figure 20). IMPORTANT: The control cable must contain som...

13 Fill if oil is below letter “L” on the ¿OOHUFDS Fill if oil is below “Add” on the GLSVWLFN Inspecting the Auger Blades/ Scraper Bar Before each session, inspect the auger blades for wear. When an auger blade edge or the scraper bar has worn down have an Authorized Service Dealer replace the auger...

14 MAINTENANCE Servicing the Spark Plug Use a NGK BPR6ES, Champion RN9YC, or BOSCH WR6DC spark plug or equivalent.1. Move snow thrower to a level surface.2. Run snow thrower until all fuel has been depleted.3. Wait until engine is cool.4. Rotate the discharge chute so that it faces forward.5. Remove...

16 MAINTENANCE Replacing the Auger V-Belt If auger v-belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt.1. Remove the drive side cover by removing the six screws as shown in (Figure 33). 2. Remove drive pulley from the auger shaft. NOTE: Nut is welded ...

17 STORAGE Storage STORING THE SNOWTHROWER Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. SNOW THROWER When snow thrower is to be stored for a period of time, clean it thor oughly, re move all dirt, grease, leaves, etc....

18 TROUBLESHOOTING Troubleshooting See appropriate section in manual unless directed to a service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Safety ignition key is not inserted. 1. Insert safety ignition key. 2. Out of fuel. 2. Fill fuel tank with fresh, clean gasoline. 3. ON/OFF ...