Page 3 - CONTENTS
CONTENTS INTRODUCTION................................................................ 5 General........................................................................ 5Driving.and.Transport.on.Public.Roads....................... 5Towing..................................................................
Page 5 - INTRODUCTION; Congratulations
INTRODUCTION 5 Congratulations Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to th...
Page 6 - Good Service; Manufacturing Number; Engine
INTRODUCTION 6 Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service.. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and ...
Page 7 - R N; IMPORTANT INFORMATION
SYMBOLS.AND.DECALS 7 R N These symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean. IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Reverse Neutral Fast Slow Choke Fuel Warning! Parking B...
Page 9 - SAFETY; Safety Instructions; General Operation
SAFETY 9 Safety Instructions These instructions are for your safety. Read them carefully. General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting. • It is recommended that someone be aware that you are mowing and can provide help in case of ...
Page 11 - Personal Safety Equipment
SAFETY 11 Personal Safety Equipment • Make sure that you have first aid equipment close at hand when using the machine. • Never use the machine when barefoot.• Always wear protective shoes or boots, preferably with steel toe caps. • Always wear approved protective glasses or a full visor when assemb...
Page 12 - Children; Never
SAFETY 12 8011-517 Never allow children to operate the machine 8011-518 Keep children away from work area Children Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will...
Page 13 - Safe Handling of Gasoline; There is risk for burns if touched.
SAFETY 13 Safe Handling of Gasoline WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. WARNING! The engine and the exhaust system become very hot during operation. There is risk for burns if touched. Allow engine ...
Page 14 - General Maintenance
SAFETY 14 8011-515 Never drive the machine in an enclosed space General Maintenance • Never operate machine in a closed area.• Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machi...
Page 16 - Transport
SAFETY 16 IMPORTANT INFORMATION The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over. WARNING! Escaping hydraulic oil under ...
Page 17 - CONTROLS; Control Locations
CONTROLS 17 This operator’s manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a four-stroke overhead valve engine. Transmission from the engine is made via belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the direction ...
Page 18 - Steering Control Levers
CONTROLS 18 8050-003 Steering controls Steering Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if th...
Page 19 - Throttle Control; USE FULL THROTTLE WHEN MOWING; mower performance and battery charging.; Parking Brake; Ignition Switch
CONTROLS 19 Throttle Control The throttle control regulates the engine speed and thereby the rate of rotation of the blades.In order to increase or decrease the engine speed, the control is moved forward or back respectively.Avoid idling the engine for long periods, as there is a risk of fouling the...
Page 20 - Choke Control; Risk for burns if touched.
CONTROLS 20 Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.For cold starts the throttle knob should be pushed forward all of the way. Refueling Read the safety instructions before refueling. The machine has one fuel tank, just behind...
Page 21 - Fuel Shut Off Valve; Mower Deck Lifting Lever; Tracking
CONTROLS 21 Fuel Shut Off Valve The fuel shut off valve is located in the fuel line under the seat. Tilt seat forward for access. The fuel valve is ON when the valve is parallel to the fuel line. Rotate the valve ¼ turn clockwise to turn fuel OFF. 8050-010 Fuel shut off valve in the OPEN position. 8...
Page 22 - Bypass Linkages; Moving Machine By Hand; Blade Control Lever; • the engine stopped
CONTROLS 22 Bypass Linkages When pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard.See Moving Machine By Hand in the Operation section. 8050-018 Set bypass linkages into slots o...
Page 23 - OPERATION; Read the; Training; Steering; To move forward and backward; Moving; To turn to the right
OPERATION 23 Read the Safety section and following pages, if you are unfamiliar with the machine. Training Due to unique steering capabilities, zero turn mowers are far more maneuverable than typical riding mowers.This section should be reviewed in its entirety prior to attempting to move the mower ...
Page 24 - Before Starting; • Read the sections Safety Instructions and; Starting the Engine; Disengage the mower blades by lowering the
OPERATION 24 Before Starting • Read the sections Safety Instructions and Controls before starting the machine. • Perform the daily maintenance before starting (see Maintenance Schedule in the Maintenance section). • Check that there is sufficient fuel in the fuel tank.• Adjust the seat to the desire...
Page 25 - Move the steering controls outward to the locked
OPERATION 25 8050-008 Set the throttle 8050-028 Place controls in neutral position 8050-007 Choke control 5. Move the steering controls outward to the locked (outer) neutral position. 6. Move the throttle to the middle position. 7. If the engine is cold, the choke control should be pushed forward to...
Page 26 - Press in and turn the ignition key to the start
OPERATION 26 8050-135 Turn to START position 8050-136 Release ignition to the RUN position 8050-010 Open the fuel valve 8. Open the fuel valve. IMPORTANT INFORMATION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying....
Page 27 - USE; Battery; Jumper cables
OPERATION 27 Slowly slide the choke control back to the middle position when the engine has started.Set the desired engine speed with the throttle. Allow the engine to run at a moderate speed, approximately mid throttle, for 3-5 minutes before loading it too heavily. USE FULL THROTTLE WHEN MOWING (n...
Page 28 - Running; Release the parking brake by moving the lever
OPERATION 28 Running 1. Release the parking brake by moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 2. Move the steeri...
Page 29 - Operating on Hills; Read the Safety Instructions
OPERATION 29 Operating on Hills Read the Safety Instructions Driving on Slopes in the Safety Instructions . • The slowest speed possible should be used before starting up or down hills. • Avoid stopping or changing speed on hills.• If stopping is absolutely necessary, pull drive levers into the neut...
Page 30 - Mowing Tips
OPERATION 30 Mowing Tips • Observe and flag rocks and other fixed objects to avoid collisions. • Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot...
Page 31 - Stopping the Engine
OPERATION 31 Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling.1. Disengage the mower deck by sliding the blad...
Page 32 - Make no adjustments without:
OPERATION 32 Moving Machine By Hand When pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard.1. Raise the deck into the highest cutting position.2. Pull the EZT bypass linkages ou...
Page 33 - MAINTENANCE; Maintenance Schedule; Maintenance
MAINTENANCE 33 Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain...
Page 34 - come in contact with the plug.
MAINTENANCE 34 1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. 2) In dusty conditions, cleaning and replacement are required more often. 3) For daily use, the machine should be lubricated twice weekly. 4) Performed by authori...
Page 35 - Cleaning battery and terminals; battery cable then RED battery cable.
MAINTENANCE 35 Battery Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.• Keep battery and terminals clean.• Keep battery bolts tight.• See chart for charging ti...
Page 36 - Safety System; Tire Pressures
MAINTENANCE 36 Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions.The engine can only be started when:1. The mower deck is disengaged.2. The steering controls are in the outer, locked neutral position. 3. The driver is sitting ...
Page 37 - Deck Belt; To replace deck belt; Carefully lift the belt away from belt keepers and
MAINTENANCE 37 Parking Brake Visually check that no damage is found on the lever, links, or switch belonging to the parking brake. Perform a standstill test and check that there is sufficient braking action.To adjust the parking brake, contact the Husqvarna service workshop. WARNING! Faulty adjustme...
Page 38 - EZT Belt; To replace EZT belt; To Replace Deck Belt; Belt installation; Cutting Blades; Blade Replacement
MAINTENANCE 38 2 1 3 WARNING! The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool before servicing. EZT Belt To replace EZT belt Park the mower on a level surface. Engage the park brake. EZT belt removal NOTE: Be car...
Page 39 - Adjusting the Mower Deck; Before performing any service or adjustment checklist:; Checking Tire Pressure; Leveling Deck; Position the mower on a level, preferably
MAINTENANCE 39 Adjusting the Mower Deck WARNING! Before performing any service or adjustment checklist: 1. Engage the parking brake.2. Place the Blade switch in the disengaged position.3. Turn ignition switch to OFF position and remove the key.4. Make sure the blades and all moving parts have comple...
Page 40 - Caster Wheels; Removal and installation of caster wheel; Cleaning; Hardware
MAINTENANCE 40 2 1 3 Caster Wheels Check every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for service.Foam filled tires or solid tires will void the warranty. Removal and installation of caster wheel 1. Remove nut (1) and caster bolt (2).2...
Page 41 - LUBRICATION; General
LUBRICATION 41 General Remove the ignition key to prevent unintentional movements during lubrication.When lubricating with an oil can, it must be filled with engine oil.When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.For daily use, the machine sho...
Page 42 - Front Wheel Mount; Engine Lubrication; Transmission
LUBRICATION 42 Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount.Use only good quality bearing grease.Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality. Front Wheel Bearings Lubricate with a grease gun, one zerk for each se...
Page 43 - TROUBLESHOOTING
TROUBLESHOOTING 43 Problem / Cause Engine will not start • Blade lever is engaged• Steering controls are not locked in neutral position• Driver is not sitting in driver’s seat• Parking brake is not activated• Battery is dead• Contamination in carburetor or fuel line• Fuel supply is closed or tap for...
Page 45 - STORAGE; Winter Storage; Inspect the machine for worn or damaged parts; Service
STORAGE 45 Winter Storage The machine should be readied for storage at the end of the mowing season or if it will not be in use for longer than 30 days. Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function...
Page 47 - TECHNICAL DATA
TECHNICAL DATA 47 (1 The power rating of the engines indicated is the average net power output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from this value. Actual power output for the engine install...
Page 48 - HEX HEAD CAP SCREWS; Torque Specifications
TECHNICAL.DATA 48 HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut Shank Size (Diameter in inches, fine or coarse thread) Size ft./lbs Nm...
Page 49 - CONFORMITY.CERTIFICATES; USA requirements
49 CONFORMITY.CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these lab...
Page 50 - Action; Delivery Service
50 SERVICE.JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge battery. Adjust tire pressure of all wheels according to Technical Data. Mount the steering controls in the normal position. Connect the contact box to the cable for the seat’s safety switch. Check that the right amount...
Page 51 - After the First 10 Hours
51 SERVICE.JOURNAL Action Date, mtr reading, stamp, sign After the First 10 Hours Change engine oil. 25-Hour Service Check the fuel pump’s air filter. Check the hydraulic system’s oil level. Check the tire pressures. Lubricate the belt adjuster, mower deck. Lubricate the belt adjuster, hydraulic pum...
Page 53 - Clean the combustion chamber and grind the valve seats.; At Least Once Each Year; Replace the air filter’s paper cartridge.
53 SERVICE.JOURNAL Action Date, mtr reading, stamp, sign 300-Hour Service Perform the 25-hour service. Perform the 50-hour service. Perform the 100-hour service. Check/adjust the mower deck. Clean the combustion chamber and grind the valve seats. Check the engine valve clearance. Replace the air cle...
