Husqvarna M7 - Manual

other than the operator is 8 m(26 feet) from all sides exceptwhere the logs are rolled in.The safety distance from thisside is 15 m (50 feet), due to thedanger of the chain beingthrown out if it breaks. Anyone working with the Logo-sol M7 WoodWorkers Mill mustbe well-rested, healthy and ingood physi...

ALWAYS REMEMBER that should any type of problem occur,stop sawing and turn off thechain-saw. Most accidentswith dangerous machineshappen when somethinggoes wrong and the opera-tor attempts to fix it whilethe machine is still running.A stop seldom shows upon the finished product. During operation: To...

- Because of the high qualityand precision construction,none of the angles need setting.The only parts to adjust are theguide rail and the height of logbed, in all three bolts. - All aluminium components areanodized, creating a wearingsurface as tough as temperedsteel. It has a low frictioncoefficie...

What follows is a brief description of the M7components to assist in identifying them duringassembly. A more complete listing is found at the endof the manual. 1 Guide rail 2 Long leg 3 Horizontal beam 4 Short leg 5 Cross beam 6 Edge support 7 Log bed 8 Guide rail strut 9 Foot 10 Log rest 11 Knee jo...

11 (6) Fit the strut to the inside (D) of the guide rail flanges with the oval hole up. (4 x M6x20 collar bolts, 4 x M6 collar nuts) (5) Place the guide rail on the long legs, pressing the guide raildown while the bolts are tighte-ned. (4 x M6x20 collar bolts, 4 xM6 collar nuts) Check that the angle...

Assembly: log bed (8) Place the plastic slide rail on the log bed. Fit the longer (A) scale against the plastic rail onthe right log bed and the shorter (B) against the side of the left log bed. Do not tighten the boltsall the way. (2 x M6x30 allenhead bolts, 2 x M6 collar nuts) (9) Fit the ratchet ...

(15) The ends of the ratchet cam axle are different. Insertthe one that has the recessnearest the tip through the lowerhole in the long leg. (16) Thread the short end of the spring through the scaleselector’s spring holder and slipboth over the cam axle insidethe long leg.Now thread the axle through...

18 A 17 A Assembly: edge support (18) Slide the edge support onto the log bed. (A) Attach crank handle to the crank rod. Insert an allenwrench into the end of thethreads on the handle and tightit with an m8 locking nut. 14 (17) Thread the lifting line under the outside pulley on the liftingbeam, str...

(19) Insert bolts through the holes along the sides of both thechain-saw bed (pylon) and thespool holder plate. Turn thesquare nuts a few times. (8xM6x16 bolts, 8 x M6 squarenuts) (20) Insert the square nuts into the slide rail track, moving thespool holder plate and thechain-saw bed to opposite end...

24 (22) Fit the chain guard on the support and bolt. (2 x M6x40collar bolts, 2 x M6 locking nuts) 23 22 Remove the two bolts holdingthe guide bar and remove theguide bar cover. (23) Remove the bark grips, leaving the bolts andretightening the nuts. (24) Refit the guide bar cover, replacing the guide...

(28) Screw the handle with a washer on the threaded rod forthe log grip carriage. (1 x M6washer) (29) Insert the bolts and screw on square nuts in the same wayas when the chain-saw carriagewas assembled (see page 17).(4 x M6x16 bolts, 4 x M6 squarenuts) (30) Fit the sliding rails under the plate so ...

M7 When setting up the M7directly on the ground: The surface must firm andlevel enough that driving a normal car on it would not be aproblem. Fit a board under each pairof legs using two M6 bolts for each foot. The boards mustbe of good quality, at least50x150 mm (2”x 6”) and at least2 m (6.5 ft) lo...

(A) Check that when the log bed is cranked down, it moveseasily through the saddle platedriven by its own weight. If thisis not the case: - Stop the log bed in the positionthat you judge to be the sticki-est. If it is equally hard in allpositions, place it in its upper-most position. Lock it using t...

The guide bar should beparallel to the log bed. If this is not so, the guide bar isprobably not straight. Removethe chain from the guide barwithout removing the guide barand move the sawing unit overthe log bed. Use protective gloves! (A) Grasp the middle of the guide bar with both hands asshown and...

In the beginning it might serveyou well to make a drawing onthe top end of how you want topiece the log. Use a thickmarker so that the linecorresponds to the saw kerf. Remember that: When the log rests on a barksurface, the log bed at thetop end is set higher than theone at the root end. When a sawn...

24 Generally, once the wood issawn it must be dried.It is possible to use undriedwood in some construction, butonly keeping in mind a 7%shrinkage in width and height.While most wood shrinks some0.4% in length, this amount canusually be ignored. In order toavoid rot, you should notenclose undried woo...

25 Reasons for wrongmeasurements on anM7 sawmill. A. Incorrect adjustmentor set-up. B. Cutting equipmentmisfunction. C. Tensions in thewood. A. Checking the M7 1. Check that all four legs stand firmly and that the feet donot sink into the ground when aheavy log is loaded. 2. Sight over the log beds ...

26 Tensions in the wood cansometimes result in similarsymptoms as faults in thecutting equipment. C. Tensions in thewood The M7 sawmill can only sawstraight. If the wood grain twistsduring sawing, precision will belost. Tension can cause largevariations in measurement.Broad leaved trees have greater...

27 must learn to file before the chain gets dull. File comfortably Both hand and electrical chainfiling can give good results. Theelectrical is faster and simpler.For hand filing, we recommenda double file with a built-in filinggauge. (Pferd 4 mm, part. no.9999-000-0400).It is much easier to sharpen...

28 Logosol offers a great range of extensions, special tools and other accessories for the M7 WoodWorkers Mill. Simple extensions can be bought in 0.5 lengths (1.6 ft). It is also possible to extend theWood Workers mill to the M7Logosol Sawmill. The product catalog is available at no cost. Just orde...

29 2 Article list No. Article number # Description 1. 4507-001-1000 2 Guide rail, 2.75 m (9 ft) 2. 4507-001-1015 2 Guide railstrut 3. 4517-001-1009 1 Cross beam 4. 4507-001-1030 2 Long leg 5. 4507-001-1035 2 Short leg 6. 4507-001-1040 4 Foot 7. 4507-001-1200 2 Horizontal beam 8. 4507-001-1045 2 Knee...

EU Declaration Product: Logosol M7 portable sawmill Manufacturer: Logosol KB, Industrigatan 13SE-871 53 HärnösandTel. +46 (0)611 18285 The company hereby certifies that the Logosol M7 portable sawmill is manufactured in accordwith the specifications in Machine Directive 89/392/EEC, as amended, and i...